SLOS058C - OCTOBER 1979 - REVISED DECEMBER 2002 D A741 Operating Characteristics D Low Supply-Current Drain . . . 0.6 mA Typ D D D D D LM148 . . . J PACKAGE LM248 . . . D OR N PACKAGE LM348 . . . D, N, OR NS PACKAGE (TOP VIEW) (per amplifier) Low Input Offset Voltage Low Input Offset Current Class AB Output Stage Input/Output Overload Protection Designed to Be Interchangeable With Industry Standard LM148, LM248, and LM348 1OUT 1IN- 1 IN+ VCC+ 2IN+ 2IN- 2OUT description/ordering information 1 14 2 13 3 12 4 11 5 10 6 9 7 8 4OUT 4IN- 4IN+ VCC- 3IN+ 3IN- 3OUT LM148 . . . FK PACKAGE (TOP VIEW) 1IN- 1OUT NC 4OUT 4IN- The LM148, LM248, and LM348 are quadruple, independent, high-gain, internally compensated operational amplifiers designed to have operating characteristics similar to the A741. These amplifiers exhibit low supply-current drain and input bias and offset currents that are much less than those of the A741. 4 3 2 1 20 19 18 5 17 6 16 7 15 8 14 9 10 11 12 13 4IN+ NC VCC- NC 3IN+ 2IN- 2OUT NC 3OUT 3IN- 1IN+ NC VCC+ NC 2IN+ NC - No internal connection ORDERING INFORMATION TA VIOmax AT 25C PACKAGE PDIP (N) 0C to 70C -25C to 85C 6 mV TOP-SIDE MARKING Tube of 25 LM348N Tube of 50 LM348D Reel of 2500 LM348DR SOP (NS) Reel of 2000 LM348NSR LM348 PDIP (N) Tube of 25 LM248N LM248N Tube of 50 LM248D Reel of 2500 LM248DR Tube of 25 LM148J SOIC (D) 6 mV SOIC (D) CDIP (J) -55C 55C to 125C ORDERABLE PART NUMBER LM348N LM348 LM248 LM148J 5 mV LCCC (FK) Tube of 50 LM148FK LM148FK Package drawings, standard packing quantities, thermal data, symboliztion, and PCB design guidelines are available at www.ti.com/sc/package. Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet. Copyright 2002, Texas Instruments Incorporated !"# $"%&! '#( '"! ! $#!! $# )# # #* "# '' +,( '"! $!# - '# #!# &, !&"'# # - && $## ( $'"! !$& .. / / && $## # # #' "&# )#+ # #'( && )# $'"! $'"! $!# - '# #!# &, !&"'# # - && $## ( POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 1 SLOS058C - OCTOBER 1979 - REVISED DECEMBER 2002 symbol (each amplifier) + IN+ OUT - IN- absolute maximum ratings over operating free-air temperature range (unless otherwise noted) Supply voltage, VCC+ (see Note 1): LM148 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22 V LM248, LM348 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 V Supply voltage, VCC- (see Note 1): LM148 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -22 V LM248, LM348 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -18 V Differential input voltage, VID (see Note 2): LM148 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44 V LM248, LM348 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36 V Input voltage, VI (either input, see Notes 1 and 3): LM148 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -22 V LM248, LM348 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -18 V Duration of output short circuit (see Note 4) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Unlimited Operating virtual junction temperature,TJ . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 150C Package thermal impedance, JA (see Notes 5 and 6): D package . . . . . . . . . . . . . . . . . . . . . . . . . . . . 86C/W N package . . . . . . . . . . . . . . . . . . . . . . . . . . . . 80C/W NS package . . . . . . . . . . . . . . . . . . . . . . . . . . . 76C/W Package thermal impedance, JC (see Notes 7 and 8): FK package . . . . . . . . . . . . . . . . . . . . . . . . . 5.61C/W J package . . . . . . . . . . . . . . . . . . . . . . . . . . 15.05C/W Case temperature for 60 seconds: FK package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 260C Lead temperature 1,6 mm (1/16 inch) from case for 10 seconds: J package . . . . . . . . . . . . . . . . . . . . . 300C Lead temperature 1,6 mm (1/16 inch) from case for 60 seconds: D, N, or NS package . . . . . . . . . . . . 260C Storage temperature range, Tstg . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -65C to 150C Stresses beyond those listed under "absolute maximum ratings" may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated under "recommended operating conditions" is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability. NOTES: 1. All voltage values, unless otherwise noted, are with respect to the midpoint between VCC+ and VCC-. 2. Differential voltages are at IN+ with respect to IN-. 3. The magnitude of the input voltage must never exceed the magnitude of the supply voltage or the value specified in the table, whichever is less. 4. The output may be shorted to ground or either power supply. Temperature and/or supply voltages must be limited to ensure that the dissipation rating is not exceeded. 5. Maximum power dissipation is a function of TJ(max), JA, and TA. The maximum allowable power dissipation at any allowable ambient temperautre is PD = (TJ(max) - TA)/JA. Operating at the absolute maximum TJ of 150C can affect reliability. 6. The package thermal impedance is calculated in accordance with JESD 51-7. 7. Maximum power dissipation is a function of TJ(max), JC, and TC. The maximum allowable power dissipation at any allowable ambient temperautre is PD = (TJ(max) - TC)/JC. Operating at the absolute maximum TJ of 150C can affect reliability. 8. The package thermal impedance is calculated in accordance with MIL-STD-883. recommended operating conditions MIN MAX Supply voltage, VCC+ 4 18 V Supply voltage, VCC- -4 -18 V 2 POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 UNIT electrical characteristics at specified free-air temperature, VCC = 15 V (unless otherwise noted) LM148 TEST CONDITIONS PARAMETER MIN 25C VIO Inp t offset voltage Input oltage VO = 0 IIO Input offset current VO = 0 Full range IIB Inp t bias current Input c rrent VO = 0 Full range VICR Common-mode input voltage range RL 10 k Full range 12 RL = 2 k 25C 10 RL 2 k Full range 10 VO = 10 V, RL= 2 k 25C 50 Full range 25 25C 0.8 CMRR Common mode rejection ratio Common-mode VIC = VICRmin, VO = 0 kSVR Su ly-voltage rejection ratio Supply-voltage (VCC/VIO) VCC = 9 V to 15 V, VO = 0 IOS Short-circuit output current AVD = 1 AVD = 1 No load 4 30 50 10 10 10 25 V 160 25 160 V/mV 15 2.5 0.8 2.5 M MHz 1 1 1 25C 60 60 60 25C 70 Full range 70 25C 77 Full range 77 90 70 90 77 96 77 77 25 2.4 dB 96 dB 77 25 3.6 90 70 2.4 25C 70 70 96 V 12 10 15 0.8 nA 13 12 12 nA 200 400 12 mV 50 12 13 12 2.5 30 UNIT 6 100 500 12 160 4 200 12 MAX 7.5 125 100 12 1 25C 25C VO = 0 VO = VOM 6 TYP 7.5 25 13 MIN 25 4.5 2.4 mA 4.5 mA VO1/VO2 Crosstalk attenuation f = 1 Hz to 20 kHz 25C 120 120 120 dB All characteristics are measured under open-loop conditions with zero common-mode input voltage, unless otherwise specified. Full range for TA is -55C to 125C for LM148, -25C to 85C for LM248, and 0C to 70C for LM348. This parameter is not production tested. 3 00 0 0 Unity-gain bandwidth LM348 MAX SLOS058C - OCTOBER 1979 - REVISED FEBRUARY 2002 POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 12 B1 m 1 325 12 Input resistance S ppl current Supply c rrent (four (fo r amplifiers) 30 25C ri TYP 75 Full range Large-signal differential voltage amplification ICC 5 4 RL = 10 k AVD Phase margin 1 MIN 6 25C Maximum peak eak output out ut voltage swing g MAX Full range 25C VOM LM248 TYP SLOS058C - OCTOBER 1979 - REVISED FEBRUARY 2002 operating characteristics, VCC = 15 V, TA = 25C PARAMETER SR TEST CONDITIONS Slew rate at unity gain RL = 2 k, CL = 100 pF, See Figure 1 PARAMETER MEASUREMENT INFORMATION - VI + CL = 100 pF RL = 2 k Figure 1. Unity-Gain Amplifier 10 k 100 VI - + RL = 2 k CL = 100 pF AVD = -100 Figure 2. Inverting Amplifier 4 POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 MIN TYP 0.5 MAX UNIT V/s PACKAGE OPTION ADDENDUM www.ti.com 24-Aug-2018 PACKAGING INFORMATION Orderable Device Status (1) Package Type Package Pins Package Drawing Qty Eco Plan Lead/Ball Finish MSL Peak Temp (2) (6) (3) Op Temp (C) Device Marking (4/5) LM148FKB ACTIVE LCCC FK 20 1 TBD POST-PLATE N / A for Pkg Type -55 to 125 LM148FKB LM148J ACTIVE CDIP J 14 1 TBD A42 N / A for Pkg Type -55 to 125 LM148J LM148JB ACTIVE CDIP J 14 1 TBD A42 N / A for Pkg Type -55 to 125 LM148JB LM248D ACTIVE SOIC D 14 50 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM -25 to 85 LM248 LM248DR ACTIVE SOIC D 14 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM -25 to 85 LM248 LM248N ACTIVE PDIP N 14 25 Green (RoHS & no Sb/Br) CU NIPDAU N / A for Pkg Type -25 to 85 LM248N LM348D ACTIVE SOIC D 14 50 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM 0 to 70 LM348 LM348DG4 ACTIVE SOIC D 14 50 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM 0 to 70 LM348 LM348DR ACTIVE SOIC D 14 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM 0 to 70 LM348 LM348DRE4 ACTIVE SOIC D 14 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM 0 to 70 LM348 LM348DRG4 ACTIVE SOIC D 14 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM 0 to 70 LM348 LM348N ACTIVE PDIP N 14 25 Green (RoHS & no Sb/Br) CU NIPDAU N / A for Pkg Type 0 to 70 LM348N LM348NSR ACTIVE SO NS 14 2000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM 0 to 70 LM348 (1) The marketing status values are defined as follows: ACTIVE: Product device recommended for new designs. LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect. NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design. PREVIEW: Device has been announced but is not in production. Samples may or may not be available. OBSOLETE: TI has discontinued the production of the device. Addendum-Page 1 Samples PACKAGE OPTION ADDENDUM www.ti.com 24-Aug-2018 (2) RoHS: TI defines "RoHS" to mean semiconductor products that are compliant with the current EU RoHS requirements for all 10 RoHS substances, including the requirement that RoHS substance do not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, "RoHS" products are suitable for use in specified lead-free processes. TI may reference these types of products as "Pb-Free". RoHS Exempt: TI defines "RoHS Exempt" to mean products that contain lead but are compliant with EU RoHS pursuant to a specific EU RoHS exemption. Green: TI defines "Green" to mean the content of Chlorine (Cl) and Bromine (Br) based flame retardants meet JS709B low halogen requirements of <=1000ppm threshold. Antimony trioxide based flame retardants must also meet the <=1000ppm threshold requirement. (3) MSL, Peak Temp. - The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature. (4) There may be additional marking, which relates to the logo, the lot trace code information, or the environmental category on the device. (5) Multiple Device Markings will be inside parentheses. Only one Device Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a continuation of the previous line and the two combined represent the entire Device Marking for that device. (6) Lead/Ball Finish - Orderable Devices may have multiple material finish options. Finish options are separated by a vertical ruled line. Lead/Ball Finish values may wrap to two lines if the finish value exceeds the maximum column width. Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release. In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis. Addendum-Page 2 PACKAGE MATERIALS INFORMATION www.ti.com 14-Jul-2012 TAPE AND REEL INFORMATION *All dimensions are nominal Device Package Package Pins Type Drawing SPQ Reel Reel A0 Diameter Width (mm) (mm) W1 (mm) B0 (mm) K0 (mm) P1 (mm) W Pin1 (mm) Quadrant LM248DR SOIC D 14 2500 330.0 16.4 6.5 9.0 2.1 8.0 16.0 Q1 LM348DR SOIC D 14 2500 330.0 16.4 6.5 9.0 2.1 8.0 16.0 Q1 LM348DR SOIC D 14 2500 330.0 16.4 6.5 9.0 2.1 8.0 16.0 Q1 LM348NSR SO NS 14 2000 330.0 16.4 8.2 10.5 2.5 12.0 16.0 Q1 Pack Materials-Page 1 PACKAGE MATERIALS INFORMATION www.ti.com 14-Jul-2012 *All dimensions are nominal Device Package Type Package Drawing Pins SPQ Length (mm) Width (mm) Height (mm) LM248DR SOIC D 14 2500 367.0 367.0 38.0 LM348DR SOIC D 14 2500 333.2 345.9 28.6 LM348DR SOIC D 14 2500 367.0 367.0 38.0 LM348NSR SO NS 14 2000 367.0 367.0 38.0 Pack Materials-Page 2 PACKAGE OUTLINE J0014A CDIP - 5.08 mm max height SCALE 0.900 CERAMIC DUAL IN LINE PACKAGE PIN 1 ID (OPTIONAL) A 4X .005 MIN [0.13] .015-.060 TYP [0.38-1.52] 1 14 12X .100 [2.54] 14X .014-.026 [0.36-0.66] 14X .045-.065 [1.15-1.65] .010 [0.25] C A B .754-.785 [19.15-19.94] 8 7 B .245-.283 [6.22-7.19] .2 MAX TYP [5.08] C .13 MIN TYP [3.3] SEATING PLANE .308-.314 [7.83-7.97] AT GAGE PLANE .015 GAGE PLANE [0.38] 0 -15 TYP 14X .008-.014 [0.2-0.36] 4214771/A 05/2017 NOTES: 1. All controlling linear dimensions are in inches. Dimensions in brackets are in millimeters. Any dimension in brackets or parenthesis are for reference only. Dimensioning and tolerancing per ASME Y14.5M. 2. This drawing is subject to change without notice. 3. This package is hermitically sealed with a ceramic lid using glass frit. 4. Index point is provided on cap for terminal identification only and on press ceramic glass frit seal only. 5. Falls within MIL-STD-1835 and GDIP1-T14. www.ti.com EXAMPLE BOARD LAYOUT J0014A CDIP - 5.08 mm max height CERAMIC DUAL IN LINE PACKAGE (.300 ) TYP [7.62] SEE DETAIL A SEE DETAIL B 1 14 12X (.100 ) [2.54] SYMM 14X ( .039) [1] 8 7 SYMM LAND PATTERN EXAMPLE NON-SOLDER MASK DEFINED SCALE: 5X .002 MAX [0.05] ALL AROUND (.063) [1.6] METAL ( .063) [1.6] SOLDER MASK OPENING METAL (R.002 ) TYP [0.05] .002 MAX [0.05] ALL AROUND SOLDER MASK OPENING DETAIL A DETAIL B SCALE: 15X 13X, SCALE: 15X 4214771/A 05/2017 www.ti.com IMPORTANT NOTICE Texas Instruments Incorporated (TI) reserves the right to make corrections, enhancements, improvements and other changes to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest issue. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. TI's published terms of sale for semiconductor products (http://www.ti.com/sc/docs/stdterms.htm) apply to the sale of packaged integrated circuit products that TI has qualified and released to market. Additional terms may apply to the use or sale of other types of TI products and services. Reproduction of significant portions of TI information in TI data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such reproduced documentation. Information of third parties may be subject to additional restrictions. Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. Buyers and others who are developing systems that incorporate TI products (collectively, "Designers") understand and agree that Designers remain responsible for using their independent analysis, evaluation and judgment in designing their applications and that Designers have full and exclusive responsibility to assure the safety of Designers' applications and compliance of their applications (and of all TI products used in or for Designers' applications) with all applicable regulations, laws and other applicable requirements. Designer represents that, with respect to their applications, Designer has all the necessary expertise to create and implement safeguards that (1) anticipate dangerous consequences of failures, (2) monitor failures and their consequences, and (3) lessen the likelihood of failures that might cause harm and take appropriate actions. Designer agrees that prior to using or distributing any applications that include TI products, Designer will thoroughly test such applications and the functionality of such TI products as used in such applications. TI's provision of technical, application or other design advice, quality characterization, reliability data or other services or information, including, but not limited to, reference designs and materials relating to evaluation modules, (collectively, "TI Resources") are intended to assist designers who are developing applications that incorporate TI products; by downloading, accessing or using TI Resources in any way, Designer (individually or, if Designer is acting on behalf of a company, Designer's company) agrees to use any particular TI Resource solely for this purpose and subject to the terms of this Notice. TI's provision of TI Resources does not expand or otherwise alter TI's applicable published warranties or warranty disclaimers for TI products, and no additional obligations or liabilities arise from TI providing such TI Resources. TI reserves the right to make corrections, enhancements, improvements and other changes to its TI Resources. TI has not conducted any testing other than that specifically described in the published documentation for a particular TI Resource. Designer is authorized to use, copy and modify any individual TI Resource only in connection with the development of applications that include the TI product(s) identified in such TI Resource. NO OTHER LICENSE, EXPRESS OR IMPLIED, BY ESTOPPEL OR OTHERWISE TO ANY OTHER TI INTELLECTUAL PROPERTY RIGHT, AND NO LICENSE TO ANY TECHNOLOGY OR INTELLECTUAL PROPERTY RIGHT OF TI OR ANY THIRD PARTY IS GRANTED HEREIN, including but not limited to any patent right, copyright, mask work right, or other intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information regarding or referencing third-party products or services does not constitute a license to use such products or services, or a warranty or endorsement thereof. Use of TI Resources may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. TI RESOURCES ARE PROVIDED "AS IS" AND WITH ALL FAULTS. TI DISCLAIMS ALL OTHER WARRANTIES OR REPRESENTATIONS, EXPRESS OR IMPLIED, REGARDING RESOURCES OR USE THEREOF, INCLUDING BUT NOT LIMITED TO ACCURACY OR COMPLETENESS, TITLE, ANY EPIDEMIC FAILURE WARRANTY AND ANY IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, AND NON-INFRINGEMENT OF ANY THIRD PARTY INTELLECTUAL PROPERTY RIGHTS. TI SHALL NOT BE LIABLE FOR AND SHALL NOT DEFEND OR INDEMNIFY DESIGNER AGAINST ANY CLAIM, INCLUDING BUT NOT LIMITED TO ANY INFRINGEMENT CLAIM THAT RELATES TO OR IS BASED ON ANY COMBINATION OF PRODUCTS EVEN IF DESCRIBED IN TI RESOURCES OR OTHERWISE. IN NO EVENT SHALL TI BE LIABLE FOR ANY ACTUAL, DIRECT, SPECIAL, COLLATERAL, INDIRECT, PUNITIVE, INCIDENTAL, CONSEQUENTIAL OR EXEMPLARY DAMAGES IN CONNECTION WITH OR ARISING OUT OF TI RESOURCES OR USE THEREOF, AND REGARDLESS OF WHETHER TI HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. Unless TI has explicitly designated an individual product as meeting the requirements of a particular industry standard (e.g., ISO/TS 16949 and ISO 26262), TI is not responsible for any failure to meet such industry standard requirements. Where TI specifically promotes products as facilitating functional safety or as compliant with industry functional safety standards, such products are intended to help enable customers to design and create their own applications that meet applicable functional safety standards and requirements. Using products in an application does not by itself establish any safety features in the application. Designers must ensure compliance with safety-related requirements and standards applicable to their applications. Designer may not use any TI products in life-critical medical equipment unless authorized officers of the parties have executed a special contract specifically governing such use. Life-critical medical equipment is medical equipment where failure of such equipment would cause serious bodily injury or death (e.g., life support, pacemakers, defibrillators, heart pumps, neurostimulators, and implantables). Such equipment includes, without limitation, all medical devices identified by the U.S. Food and Drug Administration as Class III devices and equivalent classifications outside the U.S. TI may expressly designate certain products as completing a particular qualification (e.g., Q100, Military Grade, or Enhanced Product). Designers agree that it has the necessary expertise to select the product with the appropriate qualification designation for their applications and that proper product selection is at Designers' own risk. Designers are solely responsible for compliance with all legal and regulatory requirements in connection with such selection. Designer will fully indemnify TI and its representatives against any damages, costs, losses, and/or liabilities arising out of Designer's noncompliance with the terms and provisions of this Notice. Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright (c) 2018, Texas Instruments Incorporated Mouser Electronics Authorized Distributor Click to View Pricing, Inventory, Delivery & Lifecycle Information: Texas Instruments: LM348DR LM348N LM348D LM348DG4 LM348DRE4 LM348DRG4 LM348NE4 LM348NSR LM348NSRG4 LM3487QMM/NOPB LM3487QMMX/NOPB