MCC TM Micro Commercial Components P6KE6.8 THRU P6KE540(C)A omponents 20736 Marilla Street Chatsworth !"# $ % !"# Features * * Economical series Available in both unidirectional and bidirectionalconstruction and suffix"C" designates bidirectional type * Lead Free Finish/Rohs Compliant (Note1) ("P"Suffix designates Compliant. See ordering information) 600 watts peak pulse power dissipation and 5.8~459V VWM UL Recognized File # E222849 600WATTS TRANSIENT VOLTAGE SUPPRESSOR 6.8 TO 540 VOLTS Epoxy meets UL 94 V-0 flammability rating Moisture Sensitivity Level 1 * DO-15 POLARITY: Banded denotes cathode. Bidirectional not marked. WEIGHT: 0.4 Gram(Appx.). MOUNTING POSITION: Any. . Maximum Ratings D Peak Pulse Power Dissipation at 25oC: 600Watts Steady State Power Dissipatoin:5 Watts at TL=75 oC A Cathode Mark for unidirectional only 3/8" Lead Length tclamping (0 Volts to BV Min.): B Unidirectional<1x10-12 Seconds; Bidirectoinal<5x10-9 Seconds. o D o Operating and Storage Temperature: -55 C to +175 C APPLICATION C Use in sensitive electronics protection against voltage transients induced by inductive load switching and lighting on ICs, MOSFET, signal lines of sensor units for consumer, computer, industrial, automotive and telecommunication. DIMENSIONS DIM A B C D Note: INCHES MIN .230 .104 .028 1.000 MAX .300 .140 .034 --- MM MIN 5.80 2.60 .70 25.40 MAX 7.60 3.60 .90 --- NOTE 1. High Temperature Solder Exemptions Applied, see EU Directive Annex 7. Revision: A www.mccsemi.com 1 of 5 2011/01/01 MCC P6KE6.8 thru P6KE540A TM Micro Commercial Components RATINGS AND CHARACTERISTICS CURVES (TA = 25 qC unless otherwise noted) 6000 Non-repetitive Pulse Waveform shown in Fig. 3 TA = 25 C 10 1 1.0 s 100 s 10 s 1.0 ms 1000 TJ = 25 C f = 1.0 MHz Vsig = 50 mVp-p 100 10 ms Measured at Stand-off Voltage VWM 1.0 10 100 200 td - Pulse Width (sec.) V(BR) - Breakdown Voltage (V) Figure 1. Peak Pulse Power Rating Curve Figure 4. Typical Junction Capacitance Uni-Directional 6 PD, Power Dissipation (W) 100 75 50 25 60 Hz Resistive or Inductive Load 5 4 3 L = 0.375" (9.5 mm) Lead Lengths 2 1 0 0 0 25 50 75 100 125 150 175 0 200 25 50 75 100 125 150 175 TJ - Initial Temperature (C) TL - Lead Temperature (C) Figure 2. Pulse Power or Current versus Initial Junction Temperature Figure 5. Power Derating Curve 150 200 200 TJ = 25 C Pulse Width (td) is defined as the point where the peak current decays to 50 % of IPPM tr = 10 sec. Peak Value IPPM 100 IFSM - Peak Forward Surge Current (A) IPPM - Peak Pulse Current, % IRSM Measured at Zero Bias 10 0.1 0.1 s Peak Pulse Power (PPP) or Current (IPP) Derating in Percentage, % CJ, Junction Capacitance (pF) PPPM, Peak Pulse Power (kW) 100 Half Value - IPP 2 IPPM 50 10/1000 sec. Waveform as defined by R.E.A. td 0 0 Revision: A 1.0 2.0 3.0 Uni-Directional Only TJ = TJ max. 8.3 ms Single Half Sine-Wave 100 50 10 4.0 1 5 10 50 100 t - Time (ms) Number of Cycles at 60 Hz Figure 3. Pulse Waveform Figure 6. Maximum Non-Repetitive Forward Surge Current www.mccsemi.com 2 of 5 2011/01/01 MCC P6KE6.8 thru P6KE540A TM Micro Commercial Components MCC PART NUMBER P6KE6.8 P6KE6.8A P6KE7.5 P6KE7.5A P6KE8.2 P6KE8.2A P6KE9.1 P6KE9.1A P6KE10 P6KE10A P6KE11 P6KE11A P6KE12 P6KE12A P6KE13 P6KE13A P6KE15 P6KE15A P6KE16 P6KE16A P6KE18 P6KE18A P6KE20 P6KE20A P6KE22 P6KE22A P6KE24 P6KE24A P6KE27 P6KE27A P6KE30 P6KE30A P6KE33 P6KE33A P6KE36 P6KE36A P6KE39 P6KE39A P6KE43 P6KE43A P6KE47 P6KE47A P6KE51 P6KE51A P6KE56 P6KE56A P6KE62 P6KE62A P6KE68 P6KE68A Revision: A MIN (VOLTS) NOM MAX mADC V (A) V MAXIMUM PEAK PULSE CURRENT IPP A 6.12 6.45 6.75 7.13 7.38 7.79 8.19 8.65 9.0 9.5 9.9 10.5 10.8 11.4 11.7 12.4 13.5 14.3 14.4 15.2 16.2 17.1 18 19 19.8 20.9 21.6 22.8 24.3 25.7 27 28.5 29.7 31.4 32.4 34.2 35.1 37.1 38.7 40.9 42.3 44.7 45.9 48.5 50.4 53.2 55.8 58.9 61.2 64.6 6.8 6.8 7.5 7.5 8.2 8.2 9.1 9.1 10 10 11 11 12 12 13 13 15 15 16 16 18 18 20 20 22 22 24 24 27 27 30 30 33 33 36 36 39 39 43 43 47 47 51 51 56 56 62 62 68 68 7.48 7.14 8.25 7.88 9.02 8.61 10 9.55 11 10.5 12.1 11.6 13.2 12.6 14.3 13.7 16.5 15.8 17.6 16.8 19.8 18.9 22 21 24.2 23.1 26.4 25.2 29.7 28.4 33 31.5 36.3 34.7 39.6 37.8 42.9 41 47.3 45.2 51.7 49.4 56.1 53.6 61.6 58.8 68.2 65.1 74.8 71.4 10 10 10 10 10 10 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 5.5 5.8 6.05 6.4 6.63 7.02 7.37 7.78 8.1 8.55 8.92 9.4 9.72 10.2 10.5 11.1 12.1 12.8 12.9 13.6 14.5 15.3 16.2 17.1 17.8 18.8 19.4 20.5 21.8 23.1 24.3 25.6 26.8 28.2 29.1 30.8 31.6 33.3 34.8 36.8 38.1 40.2 41.3 43.6 45.4 47.8 50.2 53 55.1 58.1 1000 1000 500 500 200 200 50 50 10 10 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 10.8 10.5 11.7 11.3 12.5 12.1 13.8 13.4 15 14.5 16.2 15.6 17.3 16.7 19 18.2 22 21.2 23.5 22.5 26.5 25.2 29.1 27.7 31.9 30.6 34.7 33.2 39.1 37.5 43.5 41.4 47.7 45.7 52 49.9 56.4 53.9 61.9 59.3 67.8 64.8 73.5 70.1 80.5 77 89 85 98 92 56 57 51 53 48 50 44 45 40 41 37 38 35 36 32 33 27 28 26 27 23 24 21 22 19 20 17 18 15 16 14 14.4 12.6 13.2 11.6 12 10.6 11.2 9.6 10.1 8.9 9.3 8.2 8.6 7.4 7.8 6.8 7.1 6.1 6.5 BREAKDOWN VOLTAGE V(BR) @ IT TEST CURRENT IT RATED STANDOFF VOLTAGE VWM MAXIMUM REVERSE LEAKAGE ID @VWM MAXIMUM CLAMPING VOLTAGE VC @ IPP www.mccsemi.com 3 of 5 MAX. TEMP COEFFICIENT OF VBR V(BR) (TA) -55C TO 100C % / C .057 .057 .061 .061 .065 .065 .068 .068 .073 .073 .075 .075 .078 .078 .081 .081 .084 .084 .086 .086 .088 .088 .090 .090 .092 .092 .094 .094 .096 .096 .097 .097 .098 .098 .099 .099 .100 .100 .101 .101 .101 .101 .102 .102 .103 .103 .104 .104 .104 .104 2011/01/01 MCC P6KE6.8 thru P6KE540A TM Micro Commercial Components MCC PART NUMBER P6KE75 P6KE75A P6KE82 P6KE82A P6KE91 P6KE91A P6KE100 P6KE100A P6KE110 P6KE110A P6KE120 P6KE120A P6KE130 P6KE130A P6KE150 P6KE150A P6KE160 P6KE160A P6KE170 P6KE170A P6KE180 P6KE180A P6KE200 P6KE200A P6KE220 P6KE220A P6KE250 P6KE250A P6KE300 P6KE300A P6KE350 P6KE350A P6KE400 P6KE400A P6KE440 P6KE440A P6KE480 P6KE480A P6KE510 P6KE510A P6KE540 P6KE540A MIN (VOLTS) NOM MAX mADC V (A) V MAXIMUM PEAK PULSE CURRENT IPP A 67.5 71.3 73.8 77.9 81.9 86.5 90 95 99 105 108 114 117 124 135 143 144 152 153 161 162 171 180 190 198 209 225 237 270 285 315 332 360 380 396 418 432 456 459 485 486 513 75 75 82 82 91 91 100 100 110 110 120 120 130 130 150 150 160 160 170 170 180 180 200 200 220 220 250 250 300 300 350 350 400 400 440 440 480 480 510 510 510 510 82.5 78.8 90.2 86.1 100 95.5 110 105 121 116 132 126 143 137 165 158 176 168 187 179 198 189 220 210 242 231 275 263 330 315 385 368 440 420 484 462 528 504 561 535 594 567 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 60.7 64.1 66.4 70.1 73.7 77.8 81 85.5 89.2 94 97.2 102 105 111 121 128 130 136 138 145 146 154 162 171 175 185 202 214 243 256 284 300 324 342 356 376 389 408 413 434 437 459 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 108 103 118 113 131 125 144 137 158 152 173 165 187 179 215 207 230 219 244 234 258 246 287 274 344 328 360 344 430 414 504 482 574 548 631 600 686 658 729 698 772 740 5.5 5.8 5.1 5.3 4.5 4.8 4.2 4.4 3.8 4.0 3.5 3.6 3.2 3.3 2.8 2.9 2.6 2.7 2.5 2.6 2.3 2.4 2.1 2.2 1.8 1.9 1.7 1.8 1.4 1.5 1.2 1.3 1.05 1.1 0.99 1.04 0.88 0.91 0.82 0.86 0.78 0.81 BREAKDOWN VOLTAGE V(BR) @ IT TEST CURRENT IT RATED STANDOFF VOLTAGE VWM MAXIMUM REVERSE LEAKAGE ID @VWM MAXIMUM CLAMPING VOLTAGE VC @ IPP MAX. TEMP COEFFICIENT OF VBR V(BR) (TA) -55C TO 100C % / C .105 .105 .105 .105 .106 .106 .106 .106 .107 .107 .107 .107 .108 .108 .108 .108 .108 .108 .108 .108 .108 .108 .108 .108 .108 .108 .110 .110 .110 .110 .110 .110 .110 .110 .110 .110 .110 .110 .110 .110 .110 .110 Notes: For bidirectional types having Vwm of 10 Volts and less,the IR limit is double. For parts without A,the VBR is +/- 10%. Revision: A www.mccsemi.com 4 of 5 2011/01/01 MCC TM Micro Commercial Components Ordering Information : Device Packing Part Number-TP Tape&Reel: 4Kpcs/Reel Part Number-AP Ammo Packing: 3Kpcs/Ammo Box Part Number-BP Bulk: 25Kpcs/Carton ***IMPORTANT NOTICE*** Micro Commercial Components Corp. reserves the right to make changes without further notice to any product herein to make corrections, modifications , enhancements , improvements , or other changes . Micro Commercial Components Corp . does not assume any liability arising out of the application or use of any product described herein; neither does it convey any license under its patent rights ,nor the rights of others . The user of products in such applications shall assume all risks of such use and will agree to hold Micro Commercial Components Corp . and all the companies whose products are represented on our website, harmless against all damages. ***LIFE SUPPORT*** MCC's products are not authorized for use as critical components in life support devices or systems without the express written approval of Micro Commercial Components Corporation. ***CUSTOMER AWARENESS*** Counterfeiting of semiconductor parts is a growing problem in the industry. Micro Commercial Components (MCC) is taking strong measures to protect ourselves and our customers from the proliferation of counterfeit parts. MCC strongly encourages customers to purchase MCC parts either directly from MCC or from Authorized MCC Distributors who are listed by country on our web page cited below. Products customers buy either from MCC directly or from Authorized MCC Distributors are genuine parts, have full traceability, meet MCC's quality standards for handling and storage. MCC will not provide any warranty coverage or other assistance for parts bought from Unauthorized Sources. MCC is committed to combat this global problem and encourage our customers to do their part in stopping this practice by buying direct or from authorized distributors. www.mccsemi.com Revision: A 5 of 5 2011/01/01 3