HLMP-Q105-P0011 - FCI - Product.Express

PDM: Rev:A Released .STATUS: Printed: Jul 06, 2006

Dome Packages

The HLMP-6xxx Series dome

lamps for use as indicators use a

tinted, diffused lens to provide a

wide viewing angle with a high

on-off contrast ratio. High

brightness lamps use an untinted,

nondiffused lens to provide a

high luminous intensity within a

narrow radiation pattern.

Resistor Lamps

The HLMP-6xxx Series 5 volt

subminiature lamps with built in

current limiting resistors are for

use in applications where space is

at a premium.

Lead Configurations

All of these devices are made by

encapsulating LED chips on axial

lead frames to form molded epoxy

subminiature lamp packages. A

variety of package configuration

options is available. These

Features

• Subminiature Flat Top

Package

Ideal for Backlighting and

Light Piping Applications

• Subminiature Dome Package

Diffused Dome for Wide

Viewing Angle

Nondiffused Dome for High

Brightness

• TTL and LSTTL Compatible

5 Volt Resistor Lamps

• Available in Six Colors

• Ideal for Space Limited

Applications

• Axial Leads

• Available with Lead

Configurations for Surface

Mount and Through Hole PC

Board Mounting

Description

Flat Top Package

The HLMP-Pxxx Series flat top

lamps use an untinted, non-

diffused, truncated lens to

provide a wide radiation

pattern that is necessary for

use in backlighting

applications. The flat top lamps

are also ideal for use as

emitters in light pipe

applications.

Subminiature LED Lamps

Technical Data

HLMP-Pxxx Series

HLMP-Qxxx Series

HLMP-6xxx Series

HLMP-70xx Series

include special surface mount

lead configurations, gull wing,

yoke lead or Z-bend. Right angle

lead bends at 2.54 mm (0.100

inch) and 5.08 mm (0.200 inch)

center spacing are available for

through hole mounting. For more

information refer to Standard

SMT and Through Hole Lead

Bend Options for Subminiature

LED Lamps data sheet.

PDM: Rev:A Released .STATUS: Printed: Jul 06, 2006

DH AS High High Device

Standard AlGaAs Efficiency Perf. Emerald Outline

Red Red Red Orange Yellow Green Green Device Description[1] Drawing

P005 P105 P205 P405 P305 P505 P605 Untinted, Nondiffused, A

Flat Top

P102 P202 P402 P302 P502 Untinted, Diffused, A

Flat Top

6000 Q100 6300 Q400 6400 6500 Q600 Tinted, Diffused B

Q105 6305 Q405 6405 6505 Q605 Untinted, Nondiffused, B

High Brightness

Q150 7000 7019 7040 Tinted, Diffused, Low B

Current

Q155 Nondiffused, Low B

Current

6600 6700 6800 Tinted, Diffused, B

Resistor, 5 V, 10 mA

6620 6720 6820 Diffused, Resistor, 5 V, B

4 mA

Device Selection Guide

Part Number: HLMP-xxxx

Ordering Information

HLMX-XXXX-X X X X X

4 x 4 Prod.

Part

Number

Min. Iv Bin

Max. Iv Bin

Color Bin

Selection

Packaging

Option

PDM: Rev:A Released .STATUS: Printed: Jul 06, 2006

0.50 (0.020) REF.

0.94

1.24 (0.037)

(0.049)

2.92 (0.115)

MAX.

0.76

0.89 (0.030)

(0.035)R.

0.63

0.38(0.025)

(0.015)

2.03 (0.080)

1.78 (0.070)

0.79 (0.031)

0.53 (0.021)

0.46

0.56(0.018)

(0.022)

0.25 (0.010) MAX.

NOTE 2

0.20 (0.008) MAX.

CATHODE

1.65

1.91(0.065)

(0.075)DIA.

ANODE

11.68

10.67(0.460)

(0.420)

BOTH SIDES

0.18

0.23(0.007)

(0.009)

2.08

2.34(0.082)

(0.092)

CATHODE

STRIPE

2.21

1.96(0.087)

(0.077)

(B) Diffused and Nondiffused

Figure 1. Proper Right Angle Mounting to a PC Board to Prevent Protruding Cathode Tab from

Shorting to Anode Connection.

Package Dimensions

(A) Flat Top Lamps

NO. ANODE DOWN. YES. CATHODE DOWN.

CATHODE

TAB

NOTES:

1. ALL DIMENSIONS ARE IN MILLIMETRES (INCHES).

2. PROTRUDING SUPPORT TAB IS CONNECTED TO CATHODE LEAD.

3. LEAD POLARITY FOR AlGaAs LAMPS IS OPPOSITE TO THE LEAD

POLARITY OF SUBMINIATURE LAMPS USING OTHER TECHNOLOGIES.

0.46

0.56 (0.018)

(0.022)

1.40

1.65(0.055)

(0.065)

0.25 (0.010) MAX.

NOTE 2

0.20 (0.008) MAX.

0.50 (0.020) REF.

CATHODE

1.65

1.91(0.065)

(0.075)DIA.

ANODE

11.68

10.67(0.460)

(0.420)

BOTH SIDES

1.14

1.40 (0.045)

(0.055) 0.63

0.38 (0.025)

(0.015)

2.21

1.96(0.087)

(0.077)

0.18

0.23(0.007)

(0.009)

0.79 (0.031) MAX.

2.44

1.88(0.096)

(0.074)

2.08

2.34(0.082)

(0.092)

CATHODE

STRIPE

PDM: Rev:A Released .STATUS: Printed: Jul 06, 2006

DH AS High High

Standard AlGaAs Eff. Perf. Emerald

Parameter Red Red Red Orange Yellow Green Green Units

DC Forward Current[1] 50 30 30 30 20 30 30 mA

Peak Forward Current[2] 1000 300 90 90 60 90 90 mA

DC Forward Voltage 6 6 6 6 V

(Resistor Lamps Only)

Reverse Voltage (IR = 100 µA)5 555555V

Transient Forward Current[3] 2000 500 500 500 500 500 500 mA

(10 µs Pulse)

Operating Temperature Range: -55 to -40 to -55 to +100 -40 to -20 to

Non-Resistor Lamps +100 +100 +100 +100 °C

Resistor Lamps -40 to +85 -20 to

+85

Storage Temperature Range °C

For Thru Hole Devices 260°C for 5 Seconds

Wave Soldering Temperature

[1.6 mm (0.063 in.) from body]

For Surface Mount Devices:

Convective IR 235°C for 90 Seconds

Vapor Phase 215°C for 3 Minutes

Absolute Maximum Ratings at TA = 25°C

-55 to +100

Notes:

1. See Figure 5 for current derating vs. ambient temperature. Derating is not applicable to resistor lamps.

2. Refer to Figure 6 showing Max. Tolerable Peak Current vs. Pulse Duration to establish pulsed operating conditions.

3. The transient peak current is the maximum non-recurring peak current the device can withstand without failure. Do not

operate these lamps at this high current.

PDM: Rev:A Released .STATUS: Printed: Jul 06, 2006

Electrical/Optical Characteristics, TA = 25°C

Standard Red

Device

HLMP- Parameter Symbol Min. Typ. Max. Units Test Conditions

6000-E00xx Luminous Intensity[1] IV0.63 1.2 mcd IF = 10 mA

6000-G00xx 1.60 3.2

P005-F00xx 1.0 2.5

Forward Voltage VF1.4 1.6 2.0 V IF = 10 mA

All Reverse Breakdown VR5.0 12.0 V IR = 100 µA

Voltage

6000 Included Angle Between 2θ1/290 Deg.

Half Intensity Points[2]

P005 125

Peak Wavelength λPEAK 655 nm

Dominant Wavelength[3] λd640 nm

Spectral Line Half Width ∆λ1/2 24 nm

All Speed of Response τs15 ns

Capacitance C 100 pF VF = 0; f = 1 MHz

Thermal Resistance RθJ-PIN 170 °C/W Junction-to-Cathode

Lead

Luminous Efficacy[4] ηv65 lm/W

PDM: Rev:A Released .STATUS: Printed: Jul 06, 2006

Device

HLMP- Parameter Symbol Min. Typ. Max. Units Test Conditions

P102-F00xx 1.0 20.0

P105-L00xx 10.0 30.0

P105-NP000 25 80

Q100-M00xx 16 45

Q100-N00xx Luminous Intensity IV25.0 45.0 mcd

Q100-PQ000 40 125

Q105-P00xx 40 200

Q105-ST000 160 500

Q150-F00xx 1.0 1.8

Q155-F00xx 1.0 4.0

Q100 Forward Voltage VF1.8 2.2 V IF = 20 mA

Q150/Q155 1.6 1.8 IF = 1 mA

All Reverse Breakdown VR5.0 15.0 V IR = 100 µA

Voltage

P105 125

Q100/Q150 Included Angle Between 2θ1/290 Deg.

Half Intensity Points[2]

Q105/Q155 28

Peak Wavelength λPEAK 645 nm Measured at Peak

Dominant Wavelength[3] λd637 nm

Spectral Line Half Width ∆λ1/2 20 nm

All Speed of Response τs30 ns Exponential Time

Constant; e-t/τ

Capacitance C 30 pF VF = 0; f = 1 MHz

Thermal Resistance RθJ-PIN 170 °C/W Junction-to

Cathode Lead

Luminous Efficacy[4] ηv80 lm/W

DH AS AlGaAs Red

IF = 1 mA

IF = 20 mA

PDM: Rev:A Released .STATUS: Printed: Jul 06, 2006

Device

HLMP- Parameter Symbol Min. Typ. Max. Units Test Conditions

P202-F00xx 1.0 5.0

P205-F00xx 1.0 8.0

P205-JK000 4.0 12.5 IF = 10 mA

6300-F00xx 1.0 10.0

6300-KL000 Luminous Intensity[1] IV6.3 20.0 mcd

6305-L00xx 10.0 40.0

7000-D00xx 0.4 1.0 IF = 2 mA

6600-G00xx 1.6 5.0 VF = 5.0 Volts

6620-F00xx 1.0 2.0

All Forward Voltage VF1.5 1.8 3.0 V IF = 10 mA

(Nonresistor Lamps)

6600 9.6 13.0

IFmA VF = 5.0 V

6620 3.5 5.0

All Reverse Breakdown VR5.0 30.0 V IR = 100 µA

Voltage

P205 125

6305 Included Angle Between 2θ1/228 Deg.

Half Intensity Points[2]

All 90

Diffused

Peak Wavelength λPEAK 635 nm Measured at Peak

Dominant Wavelength[3] λd626 nm

Spectral Line Half Width ∆λ1/2 40 nm

All Speed of Response τs90 ns

Capacitance C 11 pF VF = 0; f = 1 MHz

Thermal Resistance RθJ-PIN 170 °C/W Junction-to-Cathode

Lead

Luminous Efficacy[4] ηv145 lm/W

High Efficiency Red

Forward Current

(Resistor Lamps)

PDM: Rev:A Released .STATUS: Printed: Jul 06, 2006

Device

HLMP- Parameter Symbol Min. Typ. Max. Units Test Conditions

P402-F00xx 1.0 4.0

P405-F00xx IV1.0 6

P405-JK000 Luminous Intensity 4.0 12.5 mcd IF = 10 mA

Q400-F00xx 1.0 8

Q405-H00xx 2.5 14

Forward Voltage VF1.5 1.9 3.0 V IF = 10 mA

All Reverse Breakdown VR5.0 30.0 V IR = 100 µA

Voltage

P40x Included Angle Between 125

Half Intensity Points[2] 2θ1/2Deg.

Q40x 90

Peak Wavelength λPEAK 600 nm

Dominant Wavelength[3] λd602 nm Measured at Peak

Spectral Line Half Width ∆λ1/2 40 nm

All Speed of Response τs260 ns

Capacitance C 4 pF VF = 0; f = 1 MHz

Thermal Resistance RθJ-PIN 170 °C/W Junction-to-Cathode

Lead

Luminous Efficacy[4] ηv380 lm/W

Orange

PDM: Rev:A Released .STATUS: Printed: Jul 06, 2006

Device

HLMP- Parameter Symbol Min. Typ. Max. Units Test Conditions

P302-F00xx 1.0 3.0

P305-F00xx 1.0 4.0 IF = 10 mA

6400-F00xx 1.0 9.0

6400-JK000 4.0 12.5

6405-J00xx Luminous Intensity[1] IV3.6 20 mcd

6405-MN0xx 16 50

7019-D00xx 0.4 0.6 IF = 2 mA

6700-G00xx 1.4 5.0 VF = 5.0 Volts

6720-F00xx 0.9 2.0

All Forward Voltage VF2.0 2.4 V IF = 10 mA

(Nonresistor Lamps)

6700 9.6 13.0

Forward Current IFmA VF = 5.0 V

6720 (Resistor Lamps) 3.5 5.0

All Reverse Breakdown VR5.0 50.0 V

Voltage

P305 125

6405 Included Angle Between 2θ1/228 Deg.

Half Intensity Points[2]

All 90

Diffused

Peak Wavelength λPEAK 583 nm Measured at Peak

Dominant Wavelength[3] λd585 nm

Spectral Line Half Width ∆λ1/2 36 nm

All Speed of Response τs90 ns

Capacitance C 15 pF VF = 0; f = 1 MHz

Thermal Resistance RθJ-PIN 170 °C/W Junction-to-Cathode

Lead

Luminous Efficacy[4] ηv500 lm/W

Yellow

PDM: Rev:A Released .STATUS: Printed: Jul 06, 2006

High Performance Green

Device

HLMP- Parameter Symbol Min. Typ. Max. Units Test Conditions

P502-F00xx 1.0 3.0

P505-G00xx 1.6 6.3

6500-F00xx 1.0 7.0 IF = 10 mA

6505-L00xx 10.0 40.0

7040-D00xx Luminous Intensity[1] Iv0.4 0.6 mcd IF = 2 mA

6800-G00xx 1.6 5.0 VF = 5.0 Volts

6820-F00xx 1.0 2.0

All Forward Voltage VF2.1 2.7 V IF = 10 mA

(Nonresistor Lamps)

6800 9.6 13.0

Forward Current IFmA VF = 5.0 V

6820 (Resistor Lamps) 3.5 5.0

All Reverse Breakdown VR5.0 50.0 V IR = 100 µA

Voltage

P505 125

6505 Included Angle Between 2θ1/228 Deg.

Half Intensity Points[2]

All 90

Diffused

Peak Wavelength λPEAK 565 nm

Dominant Wavelength[3] λd569 nm

Spectral Line Half Width ∆λ1/2 28 nm

All Speed of Response τs500 ns

Capacitance C 18 pF VF = 0; f = 1 MHz

Thermal Resistance RθJ-PIN 170 °C/W Junction-to-Cathode

Lead

Luminous Efficacy[4] ηv595 lm/W

Notes:

1. The luminous intensity for arrays is tested to assure a 2.1 to 1.0 matching between elements. The average luminous

intensity for an array determines its light output category bin. Arrays are binned for luminous intensity to allow Iv matching

between arrays.

2. θ1/2 is the off-axis angle where the luminous intensity is half the on-axis value.

3. Dominant wavelength, λd, is derived from the CIE Chromaticity Diagram and represents the single wavelength that defines

the color of the device.

4. Radiant intensity, Ie, in watts/steradian, may be calculated from the equation Ie =Iv/ηv, where Iv is the luminous intensity in

candelas and ηv is the luminous efficacy in lumens/watt.

PDM: Rev:A Released .STATUS: Printed: Jul 06, 2006

Device

HLMP- Parameter Symbol Min. Typ. Max. Units Test Conditions

P605-F00xx Luminous Intensity IV1.0 1.5 mcd IF = 10 mA

Q600-F00xx 1.0 1.5

Q605-F00xx 1.0 7.5

Forward Voltage VF2.2 3.0 V IF = 10 mA

All Reverse Breakdown VR5.0 V IR = 100 µA

Voltage

P605 Included Angle Between 125

Half Intensity Points[2] 2θ1/2Deg.

Q60x 90

Peak Wavelength λPEAK 558 nm

Dominant Wavelength[3] λd560 nm Measured at Peak

Spectral Line Half Width ∆λ1/2 24 nm

P605/

Q600 Speed of Response τs3100 ns

Capacitance C 35 pF VF = 0; f = 1 MHz

Thermal Resistance RθJ-PIN 170 °C/W Junction-to-Cathode

Lead

Luminous Efficacy[4] ηV656 lm/W

Emerald Green[1]

Note:

1. Please refer to Application Note 1061 for information comparing standard green and emerald green light ouptut degradation.

PDM: Rev:A Released .STATUS: Printed: Jul 06, 2006

Standard Red, DH As AlGaAs Red

Standard Red and DH AS

AlGaAs Red

High Efficiency Red, Orange,

Yellow, High Performance

Green, and Emerald Green

HER, Orange, Yellow, and

High Performance Green,

and Emerald Green

Low Current

Figure 1. Relative Intensity vs. Wavelength.

Figure 2. Forward Current vs. Forward Voltage. (Non-Resistor Lamp)

Figure 3. Relative Luminous Intensity vs. Forward Current. (Non-Resistor Lamp)

FORWARD CURRENT – mA

100

FORWARD VOLTAGE – V

0.5 1 1.5 2 2.5 3 3.5

HIGH

PERFORMANCE

GREEN,

EMERALD

GREEN

YELLOW

HIGH EFFICIENCY

RED/ORANGE

PDM: Rev:A Released .STATUS: Printed: Jul 06, 2006

Figure 4. Relative Efficiency (Luminous Intensity per Unit Current) vs. Peak Current (Non-Resistor Lamps).

Figure 5. Maximum Forward dc Current vs. Ambient Temperature. Derating Based on TJ MAX =

110 °C (Non-Resistor Lamps).

Figure 6. Maximum Tolerable Peak Current vs. Pulse Duration. (IDC MAX as per MAX Ratings) (Non-Resistor

Lamps).

Standard Red

DH As AlGaAs RedStandard Red

HER, Orange, Yellow, and High

Performance Green DH As AlGaAs Red

HER, Orange, Yellow, and

High Performance Green,

and Emerald Green

PDM: Rev:A Released .STATUS: Printed: Jul 06, 2006

Figure 9. Relative Intensity vs. Angular Displacement.

Figure 7. Resistor Lamp Forward Current vs. Forward

Voltage. Figure 8. Resistor Lamp Luminous Intensity vs.

Forward Voltage.

PDM: Rev:A Released .STATUS: Printed: Jul 06, 2006

HLMx-XXXX-X X X X X

4 x 4 Prod.

Part

Number

Min. Iv Bin

Max. Iv Bin

Color Bin

Selection

Packaging

Option

Ordering Information

Intensity Bin limits

Bin Min. Max.

A 0.10 0.20

B 0.16 0.32

C 0.25 0.50

D 0.40 0.80

E 0.63 1.25

F 1.00 2.00

G 1.60 3.20

H 2.50 5.00

J 4.00 8.00

K 6.30 12.50

L 10.00 20.00

M 16.00 32.00

N 25.00 50.00

P 40.00 80.00

Q 63.00 125.00

R 100.00 200.00

S 160.00 320.00

T 250.00 500.00

U 400.00 800.00

V 630.00 1250.00

W 1000.00 2000.00

X 1600.00 3200.00

Y 2500.00 5000.00

Color Bin limits

Package Bin Min. Max.

Emerald Green 0 Full Distribution

9 552 556

8 555 559

7 558 562

6 561 565

Green 0 Full Distribution

6 561 565

5 564 568

4 567 571

3 570 574

2 573 577

Yellow 0 Full Distribution

1 581.5 585.0

3 584.0 587.5

2 586.5 590.0

4 589.0 592.5

5 591.5 593.5

6 591.5 595.0

7 594.0 597.5

Orange 0 Full Distribution

1 596.5 600.0

2 599.0 602.5

3 601.5 604.0

4 603.8 608.2

5 606.8 611.2

6 609.8 614.2

7 612.8 617.2

8 615.8 620.2

PDM: Rev:A Released .STATUS: Printed: Jul 06, 2006

Mechanical Option

00 Straight Leads, Bulk Packaging, Quantity of 500 Parts

10 Right Angle Housing, Bulk Packaging, Quantity of 500 Parts

11 Gull Wing Leads, 12 mm Tape on 7 in. Dia. Reel, 1500 Parts per Reel

12 Gull Wing Lead, Bulk Packaging, Quantity of 500 Parts

14 Gull Wing Leads, 12 mm Tape on 13 in. Dia. Reel, 6000 Parts per Reel

21 Yoke Leads, 12 mm Tape on 7 in. Dia. Reel, 1500 Parts per Reel

22 Yoke Leads, Bulk Packaging, Quantity of 500 Parts

24 Yoke Leads, 12 mm Tape on 13 in. Dia. Reel, 6000 Parts per Reel

31 Z-Bend Leads, 12 mm Tape on 7 in. Dia. Reel, 1500 Parts per Reel

32 Z-Bend Leads, Bulk Packaging, Quantity of 500 Parts

34 Z-Bend Leads, 12 mm Tape on 13 in. Dia. Reel, 6000 Parts per Reel

1L 2.54 mm (0.100 inch) Center Lead Spacing, Long Leads; 10.4 mm (0.410 in.)

1S 2.54 mm (0.100 inch) Center Lead Spacing, Short Leads; 3.7 mm (0.145 in.)

2L 5.08 mm (0.200 inch) Center Lead Spacing, Long Leads; 10.4 mm (0.410 in.)

2S 5.08 mm (0.200 inch) Center Lead Spacing, Short Leads; 3.7 mm (0.145 in.)

Note:

All Categories are established for classification of products. Products may not be available in all categories.

Please contact your local Agilent representative for further clarification/information.

www.agilent.com/semiconductors

For product information and a complete list of

distributors, please go to our web site.

For technical assistance call:

Americas/Canada: +1 (800) 235-0312 or

(408) 654-8675

Europe: +49 (0) 6441 92460

China: 10800 650 0017

Hong Kong: (+65) 6271 2451

India, Australia, New Zealand: (+65) 6271 2394

Japan: (+81 3) 3335-8152(Domestic/Interna-

tional), or 0120-61-1280(Domestic Only)

Korea: (+65) 6271 2194

Malaysia, Singapore: (+65) 6271 2054

Taiwan: (+65) 6271 2654

Data subject to change.

Obsoletes 5988-4077EN

April 30, 2002

5988-6260EN

PDM: Rev:A Released .STATUS: Printed: Jul 06, 2006