NXP Semiconductors Data Sheet: Technical Data KEA64 Sub-Family Data Sheet Document Number S9KEA64P64M20SF0 Rev. 5, 05/2016 S9KEA64P64M20SF0 Supports the following: S9KEAZN16AMLC(R), S9KEAZN32AMLC(R), S9KEAZN64AMLC(R), S9KEAZN16AMLH(R), S9KEAZN32AMLH(R), and S9KEAZN64AMLH(R) Key features * Operating characteristics - Voltage range: 2.7 to 5.5 V - Flash write voltage range: 2.7 to 5.5 V - Temperature range (ambient): -40 to 125C * Performance - Up to 40 MHz ARM(R) Cortex-M0+ core and up to 20 MHz bus clock - Single cycle 32-bit x 32-bit multiplier - Single cycle I/O access port * Memories and memory interfaces - Up to 64 KB flash - Up to 256 B EEPROM - Up to 4 KB RAM * Clocks - Oscillator (OSC) - supports 32.768 kHz crystal or 4 MHz to 20 MHz crystal or ceramic resonator; choice of low power or high gain oscillators - Internal clock source (ICS) - internal FLL with internal or external reference, 31.25 kHz pretrimmed internal reference for 40 MHz system and core clock. - Internal 1 kHz low-power oscillator (LPO) * System peripherals - Power management module (PMC) with three power modes: Run, Wait, Stop - Low-voltage detection (LVD) with reset or interrupt, selectable trip points - Watchdog with independent clock source (WDOG) - Programmable cyclic redundancy check module (CRC) - Serial wire debug interface (SWD) - Bit manipulation engine (BME) * Security and integrity modules - 64-bit unique identification (ID) number per chip * Human-machine interface - Up to 57 general-purpose input/output (GPIO) - Two up to 8-bit keyboard interrupt modules (KBI) - External interrupt (IRQ) * Analog modules - One up to 16-channel 12-bit SAR ADC, operation in Stop mode, optional hardware trigger (ADC) - Two analog comparators containing a 6-bit DAC and programmable reference input (ACMP) * Timers - One 6-channel FlexTimer/PWM (FTM) - Two 2-channel FlexTimer/PWM (FTM) - One 2-channel periodic interrupt timer (PIT) - One real-time clock (RTC) * Communication interfaces - Two SPI modules (SPI) - Up to three UART modules (UART) - One I2C module (I2C) NXP reserves the right to change the production detail specifications as may be required to permit improvements in the design of its products. (c) 2014-2016 NXP B.V. * Package options - 64-pin LQFP - 32-pin LQFP KEA64 Sub-Family Data Sheet, Rev. 5, 05/2016 2 NXP Semiconductors Table of Contents 1 Ordering parts.......................................................................................4 1.1 Determining valid orderable parts............................................... 4 2 Part identification................................................................................. 4 4.2.2 FTM module timing....................................................... 16 4.3 Thermal specifications................................................................. 17 4.3.1 Thermal characteristics.................................................. 17 2.1 Description...................................................................................4 5 Peripheral operating requirements and behaviors................................ 18 2.2 Format.......................................................................................... 4 5.1 Core modules............................................................................... 18 2.3 Fields............................................................................................4 5.1.1 SWD electricals .............................................................18 2.4 Example....................................................................................... 5 5.2 External oscillator (OSC) and ICS characteristics.......................19 3 Ratings..................................................................................................5 5.3 NVM specifications..................................................................... 21 3.1 Thermal handling ratings............................................................. 5 5.4 Analog..........................................................................................23 3.2 Moisture handling ratings............................................................ 5 5.4.1 ADC characteristics....................................................... 23 3.3 ESD handling ratings................................................................... 6 5.4.2 Analog comparator (ACMP) electricals.........................25 3.4 Voltage and current operating ratings..........................................6 4 General................................................................................................. 7 4.1 Nonswitching electrical specifications........................................ 7 5.5 Communication interfaces........................................................... 26 5.5.1 SPI switching specifications.......................................... 26 6 Dimensions...........................................................................................29 4.1.1 DC characteristics.......................................................... 7 4.1.2 Supply current characteristics........................................ 13 7 Pinout................................................................................................... 29 4.1.3 EMC performance..........................................................15 7.1 Signal multiplexing and pin assignments.................................... 29 4.2 Switching specifications.............................................................. 15 8 Revision History...................................................................................30 4.2.1 6.1 Obtaining package dimensions.................................................... 29 Control timing................................................................ 15 KEA64 Sub-Family Data Sheet, Rev. 5, 05/2016 NXP Semiconductors 3 Ordering parts 1 Ordering parts 1.1 Determining valid orderable parts Valid orderable part numbers are provided on the web. To determine the orderable part numbers for this device, go to nxp.com and perform a part number search for the following device numbers: KEAZN64. 2 Part identification 2.1 Description Part numbers for the chip have fields that identify the specific part. You can use the values of these fields to determine the specific part you have received. 2.2 Format Part numbers for this device have the following format: Q B KEA A C FFF M T PP N 2.3 Fields This table lists the possible values for each field in the part number (not all combinations are valid): Field Description Values Q Qualification status B Memory type KEA Kinetis Auto family A Key attribute * Z = M0+ core * F = M4 W/ DSP & FPU * C= M4 W/ AP + FPU C CAN availability * N = CAN not available * (Blank) = CAN available * S = Automotive qualified * P = Prequalification * 9 = Flash * KEA Table continues on the next page... KEA64 Sub-Family Data Sheet, Rev. 5, 05/2016 4 NXP Semiconductors Ratings Field Description FFF Program flash memory size M Maskset revision T Temperature range (C) PP Package identifier N Packaging type Values * 16 = 16 KB * 32 = 32 KB * 64 = 64 KB * A = 1st Fab version * B = Revision after 1st version * C = -40 to 85 * V= -40 to 105 * M = -40 to 125 * LC = 32 LQFP (7 mm x 7 mm) * LH = 64 LQFP (10 mm x 10 mm) * R = Tape and reel * (Blank) = Trays 2.4 Example This is an example part number: S9KEAZN64AMLH 3 Ratings 3.1 Thermal handling ratings Symbol Description Min. Max. Unit Notes TSTG Storage temperature -55 150 C 1 TSDR Solder temperature, lead-free -- 260 C 2 1. Determined according to JEDEC Standard JESD22-A103, High Temperature Storage Life. 2. Determined according to IPC/JEDEC Standard J-STD-020, Moisture/Reflow Sensitivity Classification for Nonhermetic Solid State Surface Mount Devices. 3.2 Moisture handling ratings Symbol MSL Description Moisture sensitivity level Min. Max. Unit Notes -- 3 -- 1 1. Determined according to IPC/JEDEC Standard J-STD-020, Moisture/Reflow Sensitivity Classification for Nonhermetic Solid State Surface Mount Devices. KEA64 Sub-Family Data Sheet, Rev. 5, 05/2016 NXP Semiconductors 5 Ratings 3.3 ESD handling ratings Symbol Description Min. Max. Unit Notes VHBM Electrostatic discharge voltage, human body model -6000 +6000 V 1 VCDM Electrostatic discharge voltage, charged-device model -500 +500 V 2 Latch-up current at ambient temperature of C -100 +100 mA 3 ILAT 1. Determined according to JEDEC Standard JESD22-A114, Electrostatic Discharge (ESD) Sensitivity Testing Human Body Model (HBM). 2. Determined according to JEDEC Standard JESD22-C101, Field-Induced Charged-Device Model Test Method for Electrostatic-Discharge-Withstand Thresholds of Microelectronic Components. 3. Determined according to JEDEC Standard JESD78D, IC Latch-up Test. The test produced the following results: * Test was performed at 125 C case temperature (Class II). * I/O pins pass +100/-100 mA I-test with IDD current limit at 800 mA (VDD collapsed during positive injection). * I/O pins pass +70/-100 mA I-test with IDD current limit at 1000 mA for VDD. * Supply groups pass 1.5 Vccmax. * RESET_B pin was only tested with negative I-test due to product conditioning requirement. 3.4 Voltage and current operating ratings Absolute maximum ratings are stress ratings only, and functional operation at the maxima is not guaranteed. Stress beyond the limits specified in the following table may affect device reliability or cause permanent damage to the device. For functional operating conditions, refer to the remaining tables in this document. This device contains circuitry protecting against damage due to high static voltage or electrical fields; however, it is advised that normal precautions be taken to avoid application of any voltages higher than maximum-rated voltages to this high-impedance circuit. Reliability of operation is enhanced if unused inputs are tied to an appropriate logic voltage level (for instance, either VSS or VDD) or the programmable pullup resistor associated with the pin is enabled. Table 1. Voltage and current operating ratings Symbol Description Min. Max. Unit VDD Digital supply voltage -0.3 6.0 V IDD Maximum current into VDD -- 120 mA VIN ID VDDA 0.31 Input voltage except true open drain pins -0.3 VDD + Input voltage of true open drain pins -0.3 6 V Instantaneous maximum current single pin limit (applies to all port pins) -25 25 mA VDD - 0.3 VDD + 0.3 V Analog supply voltage V 1. Maximum rating of VDD also applies to VIN. KEA64 Sub-Family Data Sheet, Rev. 5, 05/2016 6 NXP Semiconductors General 4 General 4.1 Nonswitching electrical specifications 4.1.1 DC characteristics This section includes information about power supply requirements and I/O pin characteristics. Table 2. DC characteristics Min Typical1 Max Unit -- 2.7 -- 5.5 V 5 V, Iload = -5 mA VDD - 0.8 -- -- V 3 V, Iload = -2.5 mA VDD - 0.8 -- -- V High current drive pins, high-drive strength2 5 V, Iload = -20 mA VDD - 0.8 -- -- V 3 V, Iload = -10 mA VDD - 0.8 -- -- V Output high current Max total IOH for all ports 5V -- -- -100 mA 3V -- -- -60 Output low voltage All I/O pins, standard-drive strength 5 V, Iload = 5 mA -- -- 0.8 V 3 V, Iload = 2.5 mA -- -- 0.8 V 5 V, Iload =20 mA -- -- 0.8 V 3 V, Iload = 10 mA -- -- 0.8 V 5V -- -- 100 mA 3V -- -- 60 4.5VDD<5.5 V 0.65 x VDD -- -- 2.7VDD<4.5 V 0.70 x VDD -- -- 4.5VDD<5.5 V -- -- 0.35 x VDD 2.7VDD<4.5 V -- -- 0.30 x VDD Symbol Descriptions -- VOH IOHT VOL IOLT VIH VIL Operating voltage Output high voltage All I/O pins, except PTA2 and PTA3, standard-drive strength High current drive pins, high-drive strength2 Output low current Max total IOL for all ports Input high voltage All digital inputs Input low voltage All digital inputs V V Vhys Input hysteresis All digital inputs -- 0.06 x VDD -- -- mV |IIn| Input leakage current Per pin (pins in high impedance input mode) VIN = VDD or VSS -- 0.1 1 A Table continues on the next page... KEA64 Sub-Family Data Sheet, Rev. 5, 05/2016 NXP Semiconductors 7 Nonswitching electrical specifications Table 2. DC characteristics (continued) Symbol Descriptions Min Typical1 Max Unit |IINTOT| Total leakage combined for all port pins Pins in high impedance input mode VIN = VDD or VSS -- -- 2 A RPU Pullup resistors All digital inputs, when enabled (all I/O pins other than PTA2 and PTA3) -- 30.0 -- 50.0 k RPU3 Pullup resistors PTA2 and PTA3 pins -- 30.0 -- 60.0 k IIC DC injection current4, Single pin limit VIN < VSS, VIN > VDD -2 -- 2 mA -5 -- 25 5, 6 Total MCU limit, includes sum of all stressed pins CIn Input capacitance, all pins -- -- -- 7 pF VRAM RAM retention voltage -- 2.0 -- -- V 1. Typical values are measured at 25 C. Characterized, not tested. 2. Only PTB4, PTB5, PTD0, PTD1, PTE0, PTE1, PTH0, and PTH1 support high current output. 3. The specified resistor value is the actual value internal to the device. The pullup value may appear higher when measured externally on the pin. 4. All functional non-supply pins, except for PTA2 and PTA3, are internally clamped to VSS and VDD. PTA2 and PTA3 are true open drain I/O pins that are internally clamped to VSS. 5. Input must be current limited to the value specified. To determine the value of the required current-limiting resistor, calculate resistance values for positive and negative clamp voltages, then use the larger value. 6. Power supply must maintain regulation within operating VDD range during instantaneous and operating maximum current conditions. If the positive injection current (VIn > VDD) is higher than IDD, the injection current may flow out of VDD and could result in external power supply going out of regulation. Ensure that external VDD load will shunt current higher than maximum injection current when the MCU is not consuming power, such as when no system clock is present, or clock rate is very low (which would reduce overall power consumption). Table 3. LVD and POR specification Symbol Min Typ Max Unit 1.5 1.75 2.0 V 4.2 4.3 4.4 V Level 1 falling (LVWV = 00) 4.3 4.4 4.5 V Level 2 falling (LVWV = 01) 4.5 4.5 4.6 V VLVW3H Level 3 falling (LVWV = 10) 4.6 4.6 4.7 V VLVW4H Level 4 falling (LVWV = 11) 4.7 4.7 4.8 V -- 100 -- mV VPOR VLVDH VLVW1H VLVW2H VHYSH Description POR re-arm voltage1 Falling low-voltage detect threshold--high range (LVDV = 1)2 Falling lowvoltage warning threshold-- high range High range low-voltage detect/ warning hysteresis Table continues on the next page... KEA64 Sub-Family Data Sheet, Rev. 5, 05/2016 8 NXP Semiconductors Nonswitching electrical specifications Table 3. LVD and POR specification (continued) Symbol Description Min Typ Max Unit VLVDL Falling low-voltage detect threshold--low range (LVDV = 0) 2.56 2.61 2.66 V VLVW1L Falling lowvoltage warning threshold--low range Level 1 falling (LVWV = 00) 2.62 2.7 2.78 V Level 2 falling (LVWV = 01) 2.72 2.8 2.88 V VLVW3L Level 3 falling (LVWV = 10) 2.82 2.9 2.98 V VLVW4L Level 4 falling (LVWV = 11) 2.92 3.0 3.08 V VLVW2L VHYSDL Low range low-voltage detect hysteresis -- 40 -- mV VHYSWL Low range low-voltage warning hysteresis -- 80 -- mV VBG Buffered bandgap output 3 1.14 1.16 1.18 V 1. Maximum is highest voltage that POR is guaranteed. 2. Rising thresholds are falling threshold + hysteresis. 3. voltage Factory trimmed at VDD = 5.0 V, Temp = 125 C VDD-VOH(V) IOH(mA) Figure 1. Typical VDD-VOH Vs. IOH (standard drive strength) (VDD = 5 V) KEA64 Sub-Family Data Sheet, Rev. 5, 05/2016 NXP Semiconductors 9 Nonswitching electrical specifications VDD-VOH(V) IOH(mA) Figure 2. Typical VDD-VOH Vs. IOH (standard drive strength) (VDD = 3 V) VDD-VOH(V) IOH(mA) Figure 3. Typical VDD-VOH Vs. IOH (high drive strength) (VDD = 5 V) KEA64 Sub-Family Data Sheet, Rev. 5, 05/2016 10 NXP Semiconductors Nonswitching electrical specifications VDD-VOH(V) IOH(mA) Figure 4. Typical VDD-VOH Vs. IOH (high drive strength) (VDD = 3 V) VOL(V) IOL(mA) Figure 5. Typical VOL Vs. IOL (standard drive strength) (VDD = 5 V) KEA64 Sub-Family Data Sheet, Rev. 5, 05/2016 NXP Semiconductors 11 Nonswitching electrical specifications VOL(V) IOL(mA) Figure 6. Typical VOL Vs. IOL (standard drive strength) (VDD = 3 V) VOL(V) IOL(mA) Figure 7. Typical VOL Vs. IOL (high drive strength) (VDD = 5 V) KEA64 Sub-Family Data Sheet, Rev. 5, 05/2016 12 NXP Semiconductors Nonswitching electrical specifications VOL(V) IOL(mA) Figure 8. Typical VOL Vs. IOL (high drive strength) (VDD = 3 V) 4.1.2 Supply current characteristics This section includes information about power supply current in various operating modes. Table 4. Supply current characteristics Parameter Symbol Bus Freq VDD (V) Typical1 Max Unit Temp Run supply current FEI mode, all modules clocks enabled; run from flash RIDD 20 MHz 5 mA -40 to 125 C mA -40 to 125 C 6.7 -- 10 MHz 4.5 -- 1 MHz 1.5 -- 6.6 -- 10 MHz 4.4 -- 1 MHz 1.45 -- 5.3 -- 3.7 -- 1.5 -- 5.3 -- 10 MHz 3.7 -- 1 MHz 1.4 -- 20 MHz Run supply current FEI mode, all modules clocks disabled; run from flash RIDD 20 MHz 3 5 10 MHz 1 MHz 20 MHz 3 Table continues on the next page... KEA64 Sub-Family Data Sheet, Rev. 5, 05/2016 NXP Semiconductors 13 Nonswitching electrical specifications Table 4. Supply current characteristics (continued) Parameter Symbol Bus Freq VDD (V) Typical1 Max Unit Temp Run supply current FBE mode, all modules clocks enabled; run from RAM RIDD 20 MHz 5 9 14.8 mA -40 to 125 C 10 MHz 5.2 -- 1 MHz 1.45 -- 8.8 11.8 10 MHz 5.1 -- 1 MHz 1.4 -- 8 12.3 mA -40 to 125 C 4.4 -- mA -40 to 125 C A -40 to 125 C 20 MHz Run supply current FBE mode, all modules clocks disabled; run from RAM RIDD 20 MHz 5 10 MHz 1 MHz 1.35 -- 7.8 9.2 10 MHz 4.2 -- 1 MHz 1.3 -- 5.5 7 10 MHz 3.5 -- 1 MHz 1.4 -- 5.4 6.9 10 MHz 3.4 -- 1 MHz 1.4 -- 20 MHz Wait mode current FEI mode, all modules clocks enabled 3 WIDD 20 MHz 20 MHz Stop mode supply current no clocks active (except 1 kHz LPO clock)2 SIDD ADC adder to Stop -- 3 5 3 -- 5 2 145 -- 3 1.9 135 -- 5 86 (64-pin packages) -- ADLPC = 1 -40 to 125 C A -40 to 125 C A -40 to 125 C A -40 to 125 C 42 (32-pin package) ADLSMP = 1 ADCO = 1 3 MODE = 10B 82 (64-pin packages) -- 41 (32-pin package) ADICLK = 11B ACMP adder to Stop -- -- LVD adder to stop3 -- -- 5 12 -- 3 12 -- 5 128 -- 3 124 -- 1. Data in Typical column was characterized at 5.0 V, 25 C or is typical recommended value. 2. RTC adder causes IDD to increase typically by less than 1 A; RTC clock source is 1 kHz LPO clock. 3. LVD is periodically woken up from Stop by 5% duty cycle. The period is equal to or less than 2 ms. KEA64 Sub-Family Data Sheet, Rev. 5, 05/2016 14 NXP Semiconductors Switching specifications 4.1.3 EMC performance Electromagnetic compatibility (EMC) performance is highly dependent on the environment in which the MCU resides. Board design and layout, circuit topology choices, location and characteristics of external components as well as MCU software operation play a significant role in EMC performance. The system designer must consult the following NXP applications notes, available on nxp.com for advice and guidance specifically targeted at optimizing EMC performance. * AN2321: Designing for Board Level Electromagnetic Compatibility * AN1050: Designing for Electromagnetic Compatibility (EMC) with HCMOS Microcontrollers * AN1263: Designing for Electromagnetic Compatibility with Single-Chip Microcontrollers * AN2764: Improving the Transient Immunity Performance of Microcontroller-Based Applications * AN1259: System Design and Layout Techniques for Noise Reduction in MCUBased Systems 4.2 Switching specifications 4.2.1 Control timing Table 5. Control timing Num Rating Symbol Min Typical1 Max Unit 1 System and core clock fSys DC -- 40 MHz 2 Bus frequency (tcyc = 1/fBus) fBus DC -- 20 MHz 3 Internal low power oscillator frequency fLPO 0.67 1.0 1.25 KHz textrst 1.5 x -- -- ns 4 External reset pulse width2 tcyc 5 6 7 8 Reset low drive trstdrv 34 x tcyc -- -- ns Asynchronous path2 tILIH 100 -- -- ns Synchronous path3 tIHIL 1.5 x tcyc -- -- ns Keyboard interrupt pulse width Asynchronous path2 tILIH 100 -- -- ns Synchronous path tIHIL 1.5 x tcyc -- -- ns Port rise and fall time Normal drive strength (load = 50 pF)4 -- tRise -- 10.2 -- ns tFall -- 9.5 -- ns Port rise and fall time - high drive strength (load = 50 pF)4 -- tRise -- 5.4 -- ns tFall -- 4.6 -- ns IRQ pulse width KEA64 Sub-Family Data Sheet, Rev. 5, 05/2016 NXP Semiconductors 15 Switching specifications 1. Typical values are based on characterization data at VDD = 5.0 V, 25 C unless otherwise stated. 2. This is the shortest pulse that is guaranteed to be recognized as a RESET pin request. 3. This is the minimum pulse width that is guaranteed to pass through the pin synchronization circuitry. Shorter pulses may or may not be recognized. In stop mode, the synchronizer is bypassed so shorter pulses can be recognized. 4. Timing is shown with respect to 20% VDD and 80% VDD levels. Temperature range -40 C to 125 C. textrst RESET_b pin Figure 9. Reset timing tIHIL KBIPx IRQ/KBIPx tILIH Figure 10. KBIPx timing 4.2.2 FTM module timing Synchronizer circuits determine the shortest input pulses that can be recognized or the fastest clock that can be used as the optional external source to the timer counter. These synchronizers operate from the current bus rate clock. Table 6. FTM input timing Function Symbol Min Max Unit External clock frequency fTCLK 0 fBus/4 Hz External clock period tTCLK 4 -- tcyc External clock high time tclkh 1.5 -- tcyc External clock low time tclkl 1.5 -- tcyc Input capture pulse width tICPW 1.5 -- tcyc tTCLK tclkh TCLK tclkl Figure 11. Timer external clock KEA64 Sub-Family Data Sheet, Rev. 5, 05/2016 16 NXP Semiconductors Thermal specifications tICPW FTMCHn FTMCHn tICPW Figure 12. Timer input capture pulse 4.3 Thermal specifications 4.3.1 Thermal characteristics This section provides information about operating temperature range, power dissipation, and package thermal resistance. Power dissipation on I/O pins is usually small compared to the power dissipation in on-chip logic and voltage regulator circuits, and it is userdetermined rather than being controlled by the MCU design. To take PI/O into account in power calculations, determine the difference between actual pin voltage and VSS or VDD and multiply by the pin current for each I/O pin. Except in cases of unusually high pin current (heavy loads), the difference between pin voltage and VSS or VDD will be very small. Table 7. Thermal attributes Board type Symbol Single-layer (1S) RJA Four-layer (2s2p) Description 64 LQFP 32 LQFP Unit Notes Thermal resistance, junction to ambient (natural convection) 71 86 C/W 1, 2 RJA Thermal resistance, junction to ambient (natural convection) 53 57 C/W 1, 3 Single-layer (1S) RJMA Thermal resistance, junction to ambient (200 ft./min. air speed) 59 72 C/W 1, 3 Four-layer (2s2p) RJMA Thermal resistance, junction to ambient (200 ft./min. air speed) 46 51 C/W 1, 3 -- RJB Thermal resistance, junction to board 35 33 C/W 4 -- RJC Thermal resistance, junction to case 20 24 C/W 5 -- JT Thermal characterization parameter, junction to package top outside center (natural convection) 5 6 C/W 6 1. Junction temperature is a function of die size, on-chip power dissipation, package thermal resistance, mounting site (board) temperature, ambient temperature, air flow, power dissipation of other components on the board, and board thermal resistance. 2. Per JEDEC JESD51-2 with the single layer board (JESD51-3) horizontal. 3. Per JEDEC JESD51-6 with the board (JESD51-7) horizontal. KEA64 Sub-Family Data Sheet, Rev. 5, 05/2016 NXP Semiconductors 17 Peripheral operating requirements and behaviors 4. Thermal resistance between the die and the printed circuit board per JEDEC JESD51-8. Board temperature is measured on the top surface of the board near the package. 5. Thermal resistance between the die and the solder pad on the bottom of the package. Interface resistance is ignored. 6. Thermal characterization parameter indicating the temperature difference between package top and the junction temperature per JEDEC JESD51-2. When Greek letters are not available, the thermal characterization. The average chip-junction temperature (TJ) in C can be obtained from: TJ = TA + (PD x JA) Where: TA = Ambient temperature, C JA = Package thermal resistance, junction-to-ambient, C/W PD = Pint + PI/O Pint = IDD x VDD, Watts - chip internal power PI/O = Power dissipation on input and output pins - user determined For most applications, PI/O << Pint and can be neglected. An approximate relationship between PD and TJ (if PI/O is neglected) is: PD = K / (TJ + 273 C) Solving the equations above for K gives: K = PD x (TA + 273 C) + JA x (PD)2 where K is a constant pertaining to the particular part. K can be determined by measuring PD (at equilibrium) for an known TA. Using this value of K, the values of PD and TJ can be obtained by solving the above equations iteratively for any value of TA. 5 Peripheral operating requirements and behaviors 5.1 Core modules 5.1.1 SWD electricals Table 8. SWD full voltage range electricals Symbol J1 Description Min. Max. Unit Operating voltage 2.7 5.5 V SWD_CLK frequency of operation Table continues on the next page... KEA64 Sub-Family Data Sheet, Rev. 5, 05/2016 18 NXP Semiconductors Peripheral operating requirements and behaviors Table 8. SWD full voltage range electricals (continued) Symbol Description * Serial wire debug J2 SWD_CLK cycle period J3 SWD_CLK clock pulse width * Serial wire debug Min. Max. Unit 0 20 MHz 1/J1 -- ns 20 -- ns J4 SWD_CLK rise and fall times -- 3 ns J9 SWD_DIO input data setup time to SWD_CLK rise 10 -- ns J10 SWD_DIO input data hold time after SWD_CLK rise 3 -- ns J11 SWD_CLK high to SWD_DIO data valid -- 35 ns J12 SWD_CLK high to SWD_DIO high-Z 5 -- ns J2 J3 J3 SWD_CLK (input) J4 J4 Figure 13. Serial wire clock input timing SWD_CLK J9 SWD_DIO J10 Input data valid J11 SWD_DIO Output data valid J12 SWD_DIO J11 SWD_DIO Output data valid Figure 14. Serial wire data timing KEA64 Sub-Family Data Sheet, Rev. 5, 05/2016 NXP Semiconductors 19 Peripheral operating requirements and behaviors 5.2 External oscillator (OSC) and ICS characteristics Table 9. OSC and ICS specifications (temperature range = -40 to 125 C ambient) Num 1 Crystal or resonator frequency 2 3 4 5 6 Symbol Min Typical1 Max Unit Low range (RANGE = 0) flo 31.25 32.768 39.0625 kHz High range (RANGE = 1) fhi 4 -- 20 MHz Characteristic Load capacitors Feedback resistor See Note2 C1, C2 Low Frequency, Low-Power Mode3 RF -- -- -- M Low Frequency, High-Gain Mode -- 10 -- M High Frequency, Low-Power Mode -- 1 -- M High Frequency, High-Gain Mode -- 1 -- M -- 0 -- k -- 200 -- k -- 0 -- k Series resistor Low Frequency Low-Power Mode 3 Series resistor High Frequency Low-Power Mode3 Series resistor High Frequency, High-Gain Mode 4 MHz -- 0 -- k 8 MHz -- 0 -- k 16 MHz -- 0 -- k -- 1000 -- ms -- 800 -- ms -- 3 -- ms -- 1.5 -- ms Crystal start-up time low range = 32.768 kHz crystal; High range = 20 MHz crystal4,5 RS High-Gain Mode Low range, low power RS tCSTL Low range, high gain High range, low power tCSTH High range, high gain 7 Internal reference start-up time tIRST -- 20 50 s 8 Internal reference clock (IRC) frequency trim range fint_t 31.25 -- 39.0625 kHz 9 Internal reference clock frequency, factory trimmed, T = 125 C, VDD = 5 V fint_ft -- 31.25 -- kHz 10 DCO output frequency range FLL reference = fint_t, flo, or fhi/RDIV fdco -- -- -- MHz 11 Factory trimmed internal oscillator accuracy T = 125 C, VDD = 5 V fint_ft -0.8 -- 0.8 % 12 Deviation of IRC Over temperature range from over temperature -40 C to 125C when trimmed at T = 25 C, VDD = 5V fint_t -1 -- 0.8 % Table continues on the next page... KEA64 Sub-Family Data Sheet, Rev. 5, 05/2016 20 NXP Semiconductors Peripheral operating requirements and behaviors Table 9. OSC and ICS specifications (temperature range = -40 to 125 C ambient) (continued) Num Characteristic Symbol Min Typical1 Max Unit 13 Frequency Over temperature range from accuracy of DCO -40 C to 125C output using factory trim value fdco_ft -2.3 -- 0.8 % 14 FLL acquisition time4,6 tAcquire -- -- 2 ms 15 Long term jitter of DCO output clock (averaged over 2 ms interval)7 CJitter -- 0.02 0.2 %fdco 1. Data in Typical column was characterized at 5.0 V, 25 C or is typical recommended value. 2. See crystal or resonator manufacturer's recommendation. 3. Load capacitors (C1,C2), feedback resistor (RF) and series resistor (RS) are incorporated internally when RANGE = HGO = 0. 4. This parameter is characterized and not tested on each device. 5. Proper PC board layout procedures must be followed to achieve specifications. 6. This specification applies to any time the FLL reference source or reference divider is changed, trim value changed, or changing from FLL disabled (FBELP, FBILP) to FLL enabled (FEI, FEE, FBE, FBI). If a crystal/resonator is being used as the reference, this specification assumes it is already running. 7. Jitter is the average deviation from the programmed frequency measured over the specified interval at maximum fBus. Measurements are made with the device powered by filtered supplies and clocked by a stable external clock signal. Noise injected into the FLL circuitry via VDD and VSS and variation in crystal oscillator frequency increase the CJitter percentage for a given interval. OSC XTAL EXTAL RF C1 RS Crystal or Resonator C2 Figure 15. Typical crystal or resonator circuit KEA64 Sub-Family Data Sheet, Rev. 5, 05/2016 NXP Semiconductors 21 Peripheral operating requirements and behaviors 5.3 NVM specifications This section provides details about program/erase times and program/erase endurance for the flash and EEPROM memories. Table 10. Flash and EEPROM characteristics Characteristic Symbol Min1 Typical2 Max3 Unit4 Supply voltage for program/erase -40 C to 125 C Vprog/erase 2.7 -- 5.5 V Supply voltage for read operation VRead 2.7 -- 5.5 V NVM Bus frequency fNVMBUS 1 -- 20 MHz NVM Operating frequency fNVMOP 0.8 1 1.05 MHz Erase Verify All Blocks tVFYALL -- -- 2605 tcyc Erase Verify Flash Block tRD1BLK -- -- 2579 tcyc Erase Verify EEPROM Block tRD1BLK -- -- 810 tcyc Erase Verify Flash Section tRD1SEC -- -- 485 tcyc Erase Verify EEPROM Section tDRD1SEC -- -- 555 tcyc Read Once tRDONCE -- -- 464 tcyc Program Flash (2 word) tPGM2 0.12 0.13 0.31 ms Program Flash (4 word) tPGM4 0.21 0.21 0.49 ms Program Once tPGMONCE 0.20 0.21 0.21 ms Program EEPROM (1 Byte) tDPGM1 0.10 0.10 0.27 ms Program EEPROM (2 Byte) tDPGM2 0.17 0.18 0.43 ms Program EEPROM (3 Byte) tDPGM3 0.25 0.26 0.60 ms Program EEPROM (4 Byte) tDPGM4 0.32 0.33 0.77 ms Erase All Blocks tERSALL 95.42 100.18 100.30 ms Erase Flash Block tERSBLK 95.42 100.18 100.30 ms Erase Flash Sector tERSPG 19.10 20.05 20.09 ms Erase EEPROM Sector tDERSPG 4.81 5.05 20.57 ms Unsecure Flash tUNSECU 95.42 100.19 100.31 ms Verify Backdoor Access Key tVFYKEY -- -- 482 tcyc Set User Margin Level tMLOADU -- -- 415 tcyc FLASH Program/erase endurance TL to TH = -40 C to 125 C nFLPE 10 k 100 k -- Cycles EEPROM Program/erase endurance TL to TH = -40 C to 125 C nFLPE 50 k 500 k -- Cycles Data retention at an average junction temperature of TJavg = 85C after up to 10,000 program/erase cycles tD_ret 15 100 -- years 1. 2. 3. 4. Minimum times are based on maximum fNVMOP and maximum fNVMBUS Typical times are based on typical fNVMOP and maximum fNVMBUS Maximum times are based on typical fNVMOP and typical fNVMBUS plus aging tcyc = 1 / fNVMBUS KEA64 Sub-Family Data Sheet, Rev. 5, 05/2016 22 NXP Semiconductors Peripheral operating requirements and behaviors Program and erase operations do not require any special power sources other than the normal VDD supply. For more detailed information about program/erase operations, see the Flash Memory Module section in the reference manual. 5.4 Analog 5.4.1 ADC characteristics Table 11. 5 V 12-bit ADC operating conditions Characteri stic Supply voltage Conditions Symbol Min Typ1 Max Unit Comment Absolute VDDA 2.7 -- 5.5 V -- Delta to VDD (VDD-VDDA) VDDA -100 0 +100 mV -- Delta to VSS (VSS-VSSA) VSSA -100 0 +100 mV -- Input voltage VADIN VREFL -- VREFH V -- Input capacitance CADIN -- 4.5 5.5 pF -- Input resistance RADIN -- 3 5 k -- RAS -- -- 2 k External to MCU -- -- 5 -- -- 5 -- -- 10 -- -- 10 0.4 -- 8.0 MHz -- 0.4 -- 4.0 Ground voltage Analog source resistance * * 12-bit mode fADCK > 4 MHz fADCK < 4 MHz * * 10-bit mode fADCK > 4 MHz fADCK < 4 MHz 8-bit mode (all valid fADCK) ADC conversion clock frequency High speed (ADLPC=0) Low power (ADLPC=1) fADCK 1. Typical values assume VDDA = 5.0 V, Temp = 25C, fADCK=1.0 MHz unless otherwise stated. Typical values are for reference only and are not tested in production. KEA64 Sub-Family Data Sheet, Rev. 5, 05/2016 NXP Semiconductors 23 Peripheral operating requirements and behaviors SIMPLIFIED INPUT PIN EQUIVALENT CIRCUIT Pad leakage due to input protection ZAS R AS z ADIN SIMPLIFIED CHANNEL SELECT CIRCUIT ADC SAR ENGINE R ADIN v ADIN v AS C AS R ADIN INPUT PIN R ADIN INPUT PIN R ADIN INPUT PIN C ADIN Figure 16. ADC input impedance equivalency diagram Table 12. 12-bit ADC characteristics (VREFH = VDDA, VREFL = VSSA) Characteristic Conditions Supply current Symbol Min Typ1 Max Unit IDDA -- 133 -- A IDDA -- 218 -- A IDDA -- 327 -- A IDDA -- 582 990 A ADLPC = 1 ADLSMP = 1 ADCO = 1 Supply current ADLPC = 1 ADLSMP = 0 ADCO = 1 Supply current ADLPC = 0 ADLSMP = 1 ADCO = 1 Supply current ADLPC = 0 ADLSMP = 0 ADCO = 1 Supply current Stop, reset, module off IDDA -- 0.011 1 A ADC asynchronous clock source High speed (ADLPC = 0) fADACK 2 3.3 5 MHz Table continues on the next page... KEA64 Sub-Family Data Sheet, Rev. 5, 05/2016 24 NXP Semiconductors Peripheral operating requirements and behaviors Table 12. 12-bit ADC characteristics (VREFH = VDDA, VREFL = VSSA) (continued) Characteristic Min Typ1 Max 1.25 2 3.3 -- 20 -- -- 40 -- -- 3.5 -- -- 23.5 -- -- 5.0 -- 10-bit mode -- 1.5 2.0 8-bit mode -- 0.7 1.0 -- 1.0 -- -- 0.25 0.5 -- 0.15 0.25 -- 1.0 -- 10-bit mode -- 0.3 0.5 8-bit mode -- 0.15 0.25 -- 2.0 -- 10-bit mode -- 0.25 1.0 8-bit mode -- 0.65 1.0 -- 2.5 -- 10-bit mode -- 0.5 1.0 8-bit mode -- 0.5 1.0 -- -- 0.5 Conditions Symbol Low power (ADLPC = 1) Conversion time Short sample (including sample time) (ADLSMP = 0) tADC Long sample (ADLSMP = 1) Sample time Short sample (ADLSMP = 0) tADS Long sample (ADLSMP = 1) Total unadjusted Error2 12-bit mode Differential NonLiniarity 12-bit mode 10-bit 8-bit Integral Non-Linearity Zero-scale Full-scale error5 error6 ETUE DNL mode4 mode4 12-bit mode 12-bit mode 12-bit mode INL EZS EFS Quantization error 12 bit modes EQ Input leakage error7 all modes EIL Temp sensor slope -40 C-25 C m 25 C-125 C Temp sensor voltage 25 C VTEMP25 IIn x RAS Unit ADCK cycles ADCK cycles LSB3 LSB3 LSB3 LSB3 LSB3 LSB3 mV -- 3.266 -- -- 3.638 -- -- 1.396 -- mV/C V 1. Typical values assume VDDA = 5.0 V, Temp = 25 C, fADCK=1.0 MHz unless otherwise stated. Typical values are for reference only and are not tested in production. 2. Includes quantization 3. 1 LSB = (VREFH - VREFL)/2N 4. Monotonicity and no-missing-codes guaranteed in 10-bit and 8-bit modes 5. VADIN = VSSA 6. VADIN = VDDA 7. IIn = leakage current (refer to DC characteristics) KEA64 Sub-Family Data Sheet, Rev. 5, 05/2016 NXP Semiconductors 25 Peripheral operating requirements and behaviors 5.4.2 Analog comparator (ACMP) electricals Table 13. Comparator electrical specifications Characteristic Symbol Min Typical Max Unit Supply voltage VDDA 2.7 -- 5.5 V Supply current (Operation mode) IDDA -- 10 20 A Analog input voltage VAIN VSS - 0.3 -- VDDA V Analog input offset voltage VAIO -- -- 40 mV Analog comparator hysteresis (HYST=0) VH -- 15 20 mV Analog comparator hysteresis (HYST=1) VH -- 20 30 mV Supply current (Off mode) IDDAOFF -- 60 -- nA Propagation Delay tD -- 0.4 1 s 5.5 Communication interfaces 5.5.1 SPI switching specifications The serial peripheral interface (SPI) provides a synchronous serial bus with master and slave operations. Many of the transfer attributes are programmable. The following tables provide timing characteristics for classic SPI timing modes. See the SPI chapter of the chip's reference manual for information about the modified transfer formats used for communicating with slower peripheral devices. All timing is shown with respect to 20% VDD and 80% VDD, unless noted, and 25 pF load on all SPI pins. All timing assumes slew rate control is disabled and high-drive strength is enabled for SPI output pins. Table 14. SPI master mode timing Nu m. Symbol 1 fop 2 tSPSCK 3 tLead 4 tLag 5 tWSPSCK 6 tSU 7 Description Min. Max. Unit Comment fBus/2048 fBus/2 Hz fBus is the bus clock 2 x tBus 2048 x tBus ns tBus = 1/fBus Enable lead time 1/2 -- tSPSCK -- Enable lag time 1/2 -- tSPSCK -- tBus - 30 1024 x tBus ns -- Data setup time (inputs) 8 -- ns -- tHI Data hold time (inputs) 8 -- ns -- 8 tv Data valid (after SPSCK edge) -- 25 ns -- 9 tHO Data hold time (outputs) 20 -- ns -- Frequency of operation SPSCK period Clock (SPSCK) high or low time Table continues on the next page... KEA64 Sub-Family Data Sheet, Rev. 5, 05/2016 26 NXP Semiconductors Peripheral operating requirements and behaviors Table 14. SPI master mode timing (continued) Nu m. Symbol 10 tRI Rise time input tFI Fall time input tRO Rise time output tFO Fall time output 11 Description Min. Max. Unit Comment -- tBus - 25 ns -- -- 25 ns -- SS1 (OUTPUT) 3 2 SPSCK (CPOL=0) (OUTPUT) 10 11 10 11 4 5 5 SPSCK (CPOL=1) (OUTPUT) 6 MISO (INPUT) 7 MSB IN2 BIT 6 . . . 1 LSB IN 8 MOSI (OUTPUT) MSB OUT2 9 BIT 6 . . . 1 LSB OUT 1. If configured as an output. 2. LSBF = 0. For LSBF = 1, bit order is LSB, bit 1, ..., bit 6, MSB. Figure 17. SPI master mode timing (CPHA=0) SS1 (OUTPUT) 2 3 SPSCK (CPOL=0) (OUTPUT) 5 SPSCK (CPOL=1) (OUTPUT) 6 MISO (INPUT) 5 11 10 11 4 7 MSB IN2 BIT 6 . . . 1 LSB IN 9 8 MOSI (OUTPUT) 10 PORT DATA MASTER MSB OUT2 BIT 6 . . . 1 MASTER LSB OUT PORT DATA 1.If configured as output 2. LSBF = 0. For LSBF = 1, bit order is LSB, bit 1, ..., bit 6, MSB. Figure 18. SPI master mode timing (CPHA=1) KEA64 Sub-Family Data Sheet, Rev. 5, 05/2016 NXP Semiconductors 27 Peripheral operating requirements and behaviors Table 15. SPI slave mode timing Nu m. Symbol Description 1 fop 2 tSPSCK 3 tLead Enable lead time 4 tLag Enable lag time 5 tWSPSCK 6 tSU 7 Min. Max. Unit Comment 0 fBus/4 Hz fBus is the bus clock as defined in Control timing. 4 x tBus -- ns tBus = 1/fBus 1 -- tBus -- Frequency of operation SPSCK period 1 -- tBus -- tBus - 30 -- ns -- Data setup time (inputs) 15 -- ns -- tHI Data hold time (inputs) 25 -- ns -- 8 ta Slave access time -- tBus ns Time to data active from high-impedance state 9 tdis Slave MISO disable time -- tBus ns Hold time to highimpedance state 10 tv Data valid (after SPSCK edge) -- 25 ns -- 11 tHO Data hold time (outputs) 0 -- ns -- 12 tRI Rise time input -- tBus - 25 ns -- tFI Fall time input tRO Rise time output -- 25 ns -- tFO Fall time output 13 Clock (SPSCK) high or low time SS (INPUT) 2 12 13 12 13 4 SPSCK (CPOL=0) (INPUT) 5 3 SPSCK (CPOL=1) (INPUT) 5 9 8 MISO (OUTPUT) see note SLAVE MSB 6 MOSI (INPUT) 10 11 11 BIT 6 . . . 1 SLAVE LSB OUT SEE NOTE 7 MSB IN BIT 6 . . . 1 LSB IN NOTE: Not defined Figure 19. SPI slave mode timing (CPHA = 0) KEA64 Sub-Family Data Sheet, Rev. 5, 05/2016 28 NXP Semiconductors Dimensions SS (INPUT) 4 2 3 SPSCK (CPOL=0) (INPUT) 5 SPSCK (CPOL=1) (INPUT) 5 see note 8 MOSI (INPUT) 13 12 13 11 10 MISO (OUTPUT) 12 SLAVE MSB OUT 6 9 BIT 6 . . . 1 SLAVE LSB OUT BIT 6 . . . 1 LSB IN 7 MSB IN NOTE: Not defined Figure 20. SPI slave mode timing (CPHA=1) 6 Dimensions 6.1 Obtaining package dimensions Package dimensions are provided in package drawings. To find a package drawing, go to nxp.com and perform a keyword search for the drawing's document number: If you want the drawing for this package Then use this document number 32-pin LQFP 98ASH70029A 64-pin LQFP 98ASS23234W 7 Pinout 7.1 Signal multiplexing and pin assignments For the pin muxing details see section Signal Multiplexing and Signal Descriptions of KEA64 Reference Manual. KEA64 Sub-Family Data Sheet, Rev. 5, 05/2016 NXP Semiconductors 29 Revision History 8 Revision History The following table provides a revision history for this document. Table 16. Revision History Rev. No. Date Substantial Changes Rev. 1 11 March 2014 Initial Release Rev. 2 18 June 2014 * Parameter Classification section is removed. * Classification column is removed from all the tables in the document. * Supply current characteristics section is updated. Rev. 3 18 July 2014 * ESD handling ratings section is updated. * Figures in DC characteristics section are updated. * Specs updated in following tables: * Table 9. * Table 4. Rev. 4 03 Sept 2014 * Data Sheet type changed to "Technical Data". Rev. 5 12 May 2016 * In section: Key features, Changed the number of instances of IIC to 1. KEA64 Sub-Family Data Sheet, Rev. 5, 05/2016 30 NXP Semiconductors How to Reach Us: Home Page: nxp.com Web Support: nxp.com/support Information in this document is provided solely to enable system and software implementers to use NXP products. There are no express or implied copyright licenses granted hereunder to design or fabricate any integrated circuits based on the information in this document. NXP reserves the right to make changes without further notice to any products herein. NXP makes no warranty, representation, or guarantee regarding the suitability of its products for any particular purpose, nor does NXP assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation consequential or incidental damages. "Typical" parameters that may be provided in NXP data sheets and/or specifications can and do vary in different applications, and actual performance may vary over time. All operating parameters, including "typicals," must be validated for each customer application by customers technical experts. NXP does not convey any license under its patent rights nor the rights of others. NXP sells products pursuant to standard terms and conditions of sale, which can be found at the following address: nxp.com/SalesTermsandConditions. NXP, the NXP logo, NXP SECURE CONNECTIONS FOR A SMARTER WORLD, COOLFLUX, EMBRACE, GREENCHIP, HITAG, I2C BUS, ICODE, JCOP, LIFE VIBES, MIFARE, MIFARE CLASSIC, MIFARE DESFire, MIFARE PLUS, MIFARE FLEX, MANTIS, MIFARE ULTRALIGHT, MIFARE4MOBILE, MIGLO, NTAG, ROADLINK, SMARTLX, SMARTMX, STARPLUG, TOPFET, TRENCHMOS, UCODE, Freescale, the Freescale logo, AltiVec, C-5, CodeTest, CodeWarrior, ColdFire, ColdFire+, C-Ware, the Energy Efficient Solutions logo, Kinetis, Layerscape, MagniV, mobileGT, PEG, PowerQUICC, Processor Expert, QorIQ, QorIQ Qonverge, Ready Play, SafeAssure, the SafeAssure logo, StarCore, Symphony, VortiQa, Vybrid, Airfast, BeeKit, BeeStack, CoreNet, Flexis, MXC, Platform in a Package, QUICC Engine, SMARTMOS, Tower, TurboLink, and UMEMS are trademarks of NXP B.V. All other product or service names are the property of their respective owners. ARM, AMBA, ARM Powered, Artisan, Cortex, Jazelle, Keil, SecurCore, Thumb, TrustZone, and Vision are registered trademarks of ARM Limited (or its subsidiaries) in the EU and/or elsewhere. ARM7, ARM9, ARM11, big.LITTLE, CoreLink, CoreSight, DesignStart, Mali, mbed, NEON, POP, Sensinode, Socrates, ULINK and Versatile are trademarks of ARM Limited (or its subsidiaries) in the EU and/or elsewhere. All rights reserved. Oracle and Java are registered trademarks of Oracle and/or its affiliates. The Power Architecture and Power.org word marks and the Power and Power.org logos and related marks are trademarks and service marks licensed by Power.org. (c) 2014-2016 NXP B.V. Document Number S9KEA64P64M20SF0 Revision 5, 05/2016