ST Vishay SuperTan(R) Wet Tantalum Capacitors with Hermetic Seal FEATURES * Terminations: Standard Tin/lead (Sn/Pb) 100 % Tin (RoHS compliant) availableTerminations: * Very High Capacitance * 10 to 1800 F * 25 to 125 VDC * - 55 C to + 125 C * Very Low ESR * High Ripple Current * All Tantalum Case * Hermetically Sealed * Low DCL Pb-free Available RoHS* COMPLIANT Application Notes a) No continuous reverse voltage permissible. b)Transient reverse voltage surges are acceptable under the following conditions: The peak reverse voltage does not exceed 1.5 V and the peak current times the duration of the reverse transient does not exceed 0.05 ampere seconds. In addition, the repetition frequency of the reverse voltage surge is less than 10 Hz. c) The peak of the applied AC ripple and the applied DC voltage must not exceed the DC voltage rating of the capacitor. d) Ripple current ratings by part number at 85 C and 40 kHz are included in the table. Ripple current correction factors for other temperatures and frequencies are given on the next page. Vishay ST represents a major breakthrough in wet tantalum capacitor technology. Its unique cathode system provides the highest capacitance per unit volume. The design facilitates a doubling of capacitance, lower ESR and higher ripple current rating compared with conventional wet tantalum products. Moreover, the ST has the capacitance stability of a solid tantalum capacitor and there are no circuit impedance restrictions. The ST is housed in an all tantalum, hermetically sealed case and is manufactured to withstand hazardous environments. The ST is used widely in the defense and aerospace industries and whenever there is a space problem DIMENSIONS in inches [millimeters] TERMINAL WELDED TO CASE 0.094 (2.38) MAX. E 0.250 (6.35) MAX. 0.025 + 0.002 (0.64 + 0.05) E L "D" DIA. CASE CODE D MAX. INSULATED D 0.016 (0.41) T1 0.219 (5.56) 0.188 (4.78) T2 0.312 (7.92) 0.281 (7.14) L2 0.312 (7.92) 0.281 (7.14) T3 0.406 (10.31) 0.375 (9.52) T4 0.406 (10.31) 0.375 (9.52) NOTES: 1. Material at egress is tantalum 2. Insulation sleeving will lap over the ends of the capacitor case. TERMINAL LOCATION WITHIN 0.031 OF CENTER L + 0.031 (0.79) UNINSULATED 0.453 (11.51) 0.641 (16.28) 1.008 (25.60) 0.766 (19.46) 1.062 (26.97) Approx. Weight T1: 2.3 grams, T2: 5.7 grams T3: 9.4 grams, T4: 14.8 grams E 0.250 (6.35) MAX. 1.500 (38.10) 2.250 (57.15) 2.250 (57.15) 2.250 (57.15) 2.250 (57.15) ORDERING INFORMATION ST SUPERTAN COMMERCIAL CAP.TYPE* 220 CAPACITANCE F 100 85 C RATED DC VOLTAGE T4 CASE CODE M CAPACITANCE TOLERANCE I INSULATING SLEEVE M = 20 % M = 10 % I = Insulated X = Uninsulated E3 RoHS COMPLIANT E3 = 100 % tin termination (RoHS compliant) Blank = SnPb termination (standard design) NOTES: 1. See DSCC drawing 93026 for MIL version of SuperTan. * Pb containing terminations are not RoHS compliant, exemptions may apply www.vishay.com 1 For technical questions, contact: wettants@vishay.com Document Number: 43000 Revision: 29-MAR-07 ST Vishay SuperTan(R) Wet Tantalum Capacitors with Hermetic Seal RATINGS AND CASE CODES CAP. AT 25 C & 120 Hz (F) CASE CODE MAX. ESR 120 Hz MAX. DCL A 25 C 85 C & 125 C MAX. IMP. AT - 55 C & 120 Hz MAXIMUM CAPACITANCE CHANGE % - 55 C 85 C AC RIPPLE 85 C 40 kHz 125 C mA rms 15 VDC at 125 C + 12 1250 + 15 2100 + 30 2500 + 18 2600 + 20 3100 20 VDC at 125 C + 12 1200 + 18 1800 + 30 2200 + 18 2500 + 20 3000 30 VDC at 125 C + 15 1050 + 15 1800 + 15 2200 + 15 2100 + 20 2750 40 VDC at 125 C + 12 1050 + 15 1800 + 35 2200 + 15 2100 + 15 2750 50 VDC at 125 C +9 1050 + 10 1650 + 15 2000 + 10 2100 + 10 2750 65 VDC at 125 C + 10 1050 + 12 1650 + 15 1800 + 12 2100 + 12 2750 85 VDC at 125 C + 10 1050 + 12 1650 + 10 1800 + 12 2100 + 12 2750 PART NUMBER 25 VDC at 85 C 1.3 1 5 25 - 42 +8 ST120-25T1MI 0.83 2 10 12 - 65 + 10 ST560-25T2MI 0.5 3 25 7 - 60 + 15 ST1100-25L2MI 0.65 5 20 7 - 70 + 12 ST1200-25T3MI 0.5 6 25 7 - 72 + 12 ST1800-25T4MI 30 VDC at 85 C 100 T1 1.3 1 5 25 - 38 +8 ST100-30TMI 470 T2 0.85 2 10 15 - 65 + 10 ST470-30T2MI 950 L2 0.5 5 30 7 - 45 + 15 ST950-30L2MI 1000 T3 0.7 7 25 7 - 70 + 10 ST1000-30T3MI 1500 T4 0.6 12 35 6 - 72 + 10 ST1500-30T4MI 50 VDC at 85 C 68 T1 1.5 1 5 35 - 25 +8 ST68-50T1MI 220 T2 0.9 2 10 17.5 - 50 +8 ST220-50T2MI 450 L2 0.6 3 25 7 - 45 + 10 ST450-50L2MI 470 T3 0.75 3 25 10 - 45 +8 ST470-50T3MI 680 T4 0.7 5 40 8 - 58 + 10 ST680-50T4MI 60 VDC at 85 C 47 T1 2.0 1 5 44 - 25 +8 ST47-60T1MI 150 T2 1.1 2 10 20 - 40 +8 ST150-60T2MI 370 L2 0.6 3 25 9 - 30 + 10 ST370-60L2MI 390 T3 0.9 3 25 15 - 45 +8 ST390-60T3MI 560 T4 0.8 5 40 10 - 58 +8 ST560-60T4MI 75 VDC at 85 C 33 T1 2.5 1 5 66 - 25 +5 ST33-75T1MI 110 T2 1.3 2 10 24 - 35 +6 ST110-75T2MI 250 L2 0.8 5 30 10 - 20 +5 ST250-75L2MI 330 T3 1.0 3 30 12 - 45 +6 ST330-75T3MI 470 T4 0.9 5 50 12 - 50 +6 ST470-75T4MI 100 VDC at 85 C 15 T1 3.5 1 5 125 - 18 +3 ST15-100T1MI 68 T2 2.1 2 10 37 - 30 +4 ST68-100T2MI 120 L2 1.0 3 25 18 - 20 +5 ST120-100L2MI 150 T3 1.6 3 25 22 - 35 +6 ST150-100T3MI 220 T4 1.2 5 50 15 - 40 +6 ST220-100T4MI 125 VDC at 85 C 10 T1 5.5 1 5 175 - 15 +3 ST10-125T1MI 47 T2 2.3 2 10 47 - 25 +5 ST47-125T2MI 90 L2 1.3 5 15 24 - 15 +5 ST90-125L2MI 100 T3 1.8 3 25 35 - 35 +5 ST100-125T3MI 150 T4 1.6 5 50 20 - 35 +6 ST150-125T4MI (K = 10 %, M = 20 %) and insulation letter (I = Insulation, X = Uninsulated) * Part Numbers shown are for units with 20 % capacitance tolerance and uninsulated capacitors. For 10 units,changethe digit following the letter "X" from "0" to "9". For units with outer plastic-film insulation, substitute "2" for "0" at the end of the Part Number. * For RoHS compliant add "E3" suffix. 120 560 1100 1200 1800 T1 T2 L2 T3 T4 RIPPLE CURRENT MULTIPLIERS VERSUS FREQUENCY, TEMPERATURE AND APPLIES PEAK VOLTAGE FREQUENCY OF APPLIED RIPPLE CURRENT 120 Hz 800 Hz 1 kHz 10 kHz 40 kHz 100 kHz AMBIENT STILL 55 85 105 125 55 85 105 125 55 85 105 125 55 85 105 125 55 85 105 125 55 85 105 125 AIR TEMP. IN C 100 % % of 90 % 85 C 80 % rated 70 % peak voltage 66 2/3 % 0.60 0.60 0.60 0.60 0.60 0.39 0.46 0.52 0.35 0.58 0.44 0.60 0.46 0.27 Document Number: 43000 Revision: 29-MAR-07 0.71 0.71 0.71 0.71 0.71 0.43 0.55 0.62 0.42 0.69 0.52 0.71 0.55 0.32 0.72 0.72 0.72 0.72 0.72 0.46 0.55 0.62 0.42 0.70 0.52 0.72 0.55 0.32 0.88 0.88 0.88 0.88 0.88 0.55 0.67 0.76 0.52 0.85 0.64 0.88 0.68 0.40 For technical questions, contact: wettants@vishay.com 1.0 1.0 1.0 1.0 1.0 0.63 0.77 0.87 0.59 0.97 0.73 1.0 0.77 0.45 1.1 1.1 1.1 1.1 1.1 0.69 0.85 0.96 0.65 1.07 0.80 1.1 0.85 0.50 www.vishay.com 2 ST Vishay SuperTan(R) Wet Tantalum Capacitors with Hermetic Seal 93026 RATINGS AND CASE CODES DSCC DRAWING 93026 CAP. AT 25 C & 120 Hz (F) 93026-29 93026-30 93026-57 93026-31 93026-32 120 560 1100 1200 1800 93026-33 93026-34 93026-58 93026-35 93026-36 100 470 950 1000 1500 93026-37 93026-38 93026-59 93026-39 93026-40 68 220 450 470 680 93026-41 93026-42 93026-60 93026-43 93026-44 47 150 370 390 560 93026-45 93026-46 93026-61 93026-47 93026-48 33 110 250 330 470 93026-49 93026-50 93026-62 93026-51 93026-52 15 68 120 150 220 93026-53 93026-54 93026-63 93026-55 93026-56 10 47 90 100 150 CASE MAX. ESR CODE 120 Hz MAX. DCL A 25 VDC at 85 C T1 1.3 T2 0.83 L2 0.5 T3 0.65 T4 0.5 30 VDC at 85 C T1 1.3 T2 0.85 L2 0.5 T3 0.7 T4 0.6 50 VDC at 85 C T1 1.5 T2 0.9 L2 0.6 T3 0.75 T4 0.7 60 VDC at 85 C T1 2.0 T2 1.1 L2 0.6 T3 0.9 T4 0.8 75 VDC at 85 C T1 2.5 T2 1.3 L2 0.8 T3 1.0 T4 0.9 100 VDC at 85 C T1 3.5 T2 2.1 L2 1.0 T3 1.6 T4 1.2 125 VDC at 85 C T1 5.5 T2 2.3 L2 1.3 T3 1.8 T4 1.6 25 C 85 C & 125 C MAX. IMP. AT - 55 C & 120 Hz MAX. CAPACITANCE CHANGE % 1 2 3 5 6 5 10 25 20 25 25 12 7 7 7 - 42 - 65 - 60 - 70 - 75 1 2 5 7 12 5 10 30 25 35 25 15 7 7 6 - 38 - 65 - 45 - 70 - 72 1 2 3 3 5 5 10 25 25 40 35 17.5 7 10 8 - 25 - 50 - 25 - 50 - 58 1 2 3 3 5 5 10 25 25 40 44 20 9 15 10 - 25 - 40 - 30 - 60 - 58 1 2 5 3 5 5 10 30 30 50 66 24 10 12 12 - 25 - 35 - 20 - 45 - 55 1 2 3 3 5 5 10 25 25 50 125 37 18 22 15 - 18 - 30 - 20 - 35 - 40 1 2 5 3 5 5 10 15 25 50 175 47 24 35 20 - 15 - 25 - 15 - 35 - 35 - 55 C 85 C AC RIPPLE 85 C 40 kHz mA rms 125 C 15 VDC at 125 C +8 + 12 + 10 + 15 + 15 + 30 + 12 + 18 + 12 + 20 20 VDC at 125 C +8 + 12 + 10 + 18 + 15 + 30 + 10 + 18 + 10 + 20 30 VDC at 125 C +8 + 15 +8 + 15 + 10 + 30 +8 + 15 + 10 + 20 40 VDC at 125 C +8 + 12 +8 + 15 + 10 + 25 +8 + 15 +8 + 15 50 VDC at 125 C +5 +9 +6 + 10 +5 + 15 +6 + 10 +6 + 10 65 VDC at 125 C +3 + 10 +4 + 12 +5 + 15 +6 + 12 +6 + 12 85 VDC at 125 C +3 + 10 +5 + 12 +5 + 10 +5 + 12 +6 + 12 1250 2100 2500 2600 3100 1200 1800 2200 2500 3000 1050 1800 2200 2100 2750 1050 1650 2000 2100 2750 1050 1650 2000 2100 2750 1050 1650 1800 2100 2750 1050 1650 1800 2100 2750 ORDERING INFORMATION - DSCC PART NUMBER 93026 -29 K S DSCC DRAWING NUMBER DASH NUMBER CAPACITANCE TOLERANCE K = 10 % M = 20 % S = Sleeved U = Unsleeved DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO www.vishay.com 3 For technical questions, contact: wettants@vishay.com DRAWING NO. 93026 Document Number: 43000 Revision: 29-MAR-07 Legal Disclaimer Notice Vishay Notice Specifications of the products displayed herein are subject to change without notice. Vishay Intertechnology, Inc., or anyone on its behalf, assumes no responsibility or liability for any errors or inaccuracies. Information contained herein is intended to provide a product description only. No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document. Except as provided in Vishay's terms and conditions of sale for such products, Vishay assumes no liability whatsoever, and disclaims any express or implied warranty, relating to sale and/or use of Vishay products including liability or warranties relating to fitness for a particular purpose, merchantability, or infringement of any patent, copyright, or other intellectual property right. The products shown herein are not designed for use in medical, life-saving, or life-sustaining applications. Customers using or selling these products for use in such applications do so at their own risk and agree to fully indemnify Vishay for any damages resulting from such improper use or sale. Document Number: 91000 Revision: 08-Apr-05 www.vishay.com 1