1N5335BTA - ON Semiconductor

 Semiconductor Components Industries, LLC, 2002

June, 2002 – Rev. 2 1Publication Order Number:

1N5333B/D

1N5333B Series

5 Watt Surmetic 40

Zener Voltage Regulators

This is a complete series of 5 Watt Zener diodes with tight limits and

better operating characteristics that reflect the superior capabilities of

silicon–oxide passivated junctions. All this in an axial–lead,

transfer–molded plastic package that offers protection in all common

environmental conditions.

Specification Features:

•Zener Voltage Range – 3.3 V to 200 V

•ESD Rating of Class 3 (>16 KV) per Human Body Model

•Surge Rating of up to 180 W @ 8.3 ms

•Maximum Limits Guaranteed on up to Six Electrical Parameters

Mechanical Characteristics:

CASE: Void free, transfer–molded, thermosetting plastic

FINISH: All external surfaces are corrosion resistant and leads are

readily solderable

MAXIMUM LEAD TEMPERATURE FOR SOLDERING PURPOSES:

230°C, 1/16″ from the case for 10 seconds

POLARITY: Cathode indicated by polarity band

MOUNTING POSITION: Any

MAXIMUM RATINGS

Rating Symbol Value Unit

Max. Steady State Power Dissipation

@ TL = 75°C, Lead Length = 3/8″

Derate above 75°C

PD5

mW/°C

Operating and Storage

Temperature Range TJ, Tstg –65 to

+200 °C

Device Package Shipping

ORDERING INFORMATION

1N53xxB Axial Lead 1000 Units/Box

1N53xxBRL Axial Lead

AXIAL LEAD

CASE 17

PLASTIC

4000/Tape & Reel

Cathode Anode

53xxB

YWW

L = Assembly Location

1N53xxB = Device Code

= (See Table Next Page)

Y = Year

WW = Work Week

MARKING DIAGRAM

1N53xxBTA* Axial Lead 2000/Ammo Pack

Devices listed in

bold, italic

are ON Semiconductor

Preferred devices. Preferred devices are recommended

choices for future use and best overall value.

http://onsemi.com

*1N5361B Not Available in 2000/Ammo Pack

Zener Voltage Regulator

IZT

VZVF

1N5333B Series

http://onsemi.com

ELECTRICAL CHARACTERISTICS (TA = 25°C unless

otherwise noted, VF = 1.2 V Max @ IF = 1.0 A for all types)

Symbol Parameter

VZReverse Zener Voltage @ IZT

IZT Reverse Current

ZZT Maximum Zener Impedance @ IZT

IZK Reverse Current

ZZK Maximum Zener Impedance @ IZK

IRReverse Leakage Current @ VR

VRBreakdown Voltage

IFForward Current

VFForward Voltage @ IF

IRMaximum Surge Current @ TA = 25°C

VZReverse Zener Voltage Change

IZM Maximum DC Zener Current

1N5333B Series

http://onsemi.com

ELECTRICAL CHARACTERISTICS (TA = 25°C unless otherwise noted, VF = 1.2 V Max @ IF = 1.0 A for all types)

Zener Voltage (Note 2) Zener Impedance (Note 2) Leakage

Current

VZ

IZM

Device

VZ (Volts) @ IZT ZZT @ IZT ZZK @ IZK IZK IR @ VR

(Note 3)

V

(Note 4)

(Note 5)

(Note 1)

Marking Min Nom Max mA   AA Max Volts A Volts mA

1N5333B 1N5333B 3.14 3.3 3.47 380 3 400 1 300 1 20 0.85 1440

1N5334B 1N5334B 3.42 3.6 3.78 350 2.5 500 1 150 1 18.7 0.8 1320

1N5335B 1N5335B 3.71 3.9 4.10 320 2 500 1 50 1 17.6 0.54 1220

1N5336B 1N5336B 4.09 4.3 4.52 290 2 500 1 10 1 16.4 0.49 1100

1N5337B 1N5337B 4.47 4.7 4.94 260 2 450 1 5 1 15.3 0.44 1010

1N5338B 1N5338B 4.85 5.1 5.36 240 1.5 400 1 1 1 14.4 0.39 930

1N5339B 1N5339B 5.32 5.6 5.88 220 1 400 1 1 2 13.4 0.25 865

1N5340B 1N5340B 5.70 6.0 6.30 200 1 300 1 1 3 12.7 0.19 790

1N5341B 1N5341B 5.89 6.2 6.51 200 1 200 1 1 3 12.4 0.1 765

1N5342B 1N5342B 6.46 6.8 7.14 175 1 200 1 10 5.2 11.5 0.15 700

1N5343B 1N5343B 7.13 7.5 7.88 175 1.5 200 1 10 5.7 10.7 0.15 630

1N5344B 1N5344B 7.79 8.2 8.61 150 1.5 200 1 10 6.2 10 0.2 580

1N5345B 1N5345B 8.27 8.7 9.14 150 2 200 1 10 6.6 9.5 0.2 545

1N5346B 1N5346B 8.65 9.1 9.56 150 2 150 1 7.5 6.9 9.2 0.22 520

1N5347B 1N5347B 9.50 10 10.5 125 2 125 1 5 7.6 8.6 0.22 475

1N5348B 1N5348B 10.45 11 11.55 125 2.5 125 1 5 8.4 8.0 0.25 430

1N5349B 1N5349B 11.4 12 12.6 100 2.5 125 1 2 9.1 7.5 0.25 395

1N5350B 1N5350B 12.35 13 13.65 100 2.5 100 1 1 9.9 7.0 0.25 365

1N5351B 1N5351B 13.3 14 14.7 100 2.5 75 1 1 10.6 6.7 0.25 340

1N5352B 1N5352B 14.25 15 15.75 75 2.5 75 1 1 11.5 6.3 0.25 315

1N5353B 1N5353B 15.2 16 16.8 75 2.5 75 1 1 12.2 6.0 0.3 295

1N5354B 1N5354B 16.15 17 17.85 70 2.5 75 1 0.5 12.9 5.8 0.35 280

1N5355B 1N5355B 17.1 18 18.9 65 2.5 75 1 0.5 13.7 5.5 0.4 264

1N5356B 1N5356B 18.05 19 19.95 65 3 75 1 0.5 14.4 5.3 0.4 250

1N5357B 1N5357B 19 20 21 65 3 75 1 0.5 15.2 5.1 0.4 237

1N5358B 1N5358B 20.9 22 23.1 50 3.5 75 1 0.5 16.7 4.7 0.45 216

1N5359B 1N5359B 22.8 24 25.2 50 3.5 100 1 0.5 18.2 4.4 0.55 198

1N5360B 1N5360B 23.75 25 26.25 50 4 110 1 0.5 19 4.3 0.55 190

1N5361B* 1N5361B 25.65 27 28.35 50 5 120 1 0.5 20.6 4.1 0.6 176

1N5362B 1N5362B 26.6 28 29.4 50 6 130 1 0.5 21.2 3.9 0.6 170

1. TOLERANCE AND TYPE NUMBER DESIGNATION

The JEDEC type numbers shown indicate a tolerance of ±5%.

2. ZENER VOLTAGE (VZ) and IMPEDANCE (IZT and IZK)

Test conditions for zener voltage and impedance are as follows: IZ is applied 40 ±10 ms prior to reading. Mounting contacts are located 3/8″

to 1/2″ from the inside edge of mounting clips to the body of the diode (TA = 25°C +8°C, –2°C).

3. SURGE CURRENT (IR)

Surge current is specified as the maximum allowable peak, non–recurrent square–wave current with a pulse width, PW, of 8.3 ms. The data

given in Figure 6 may be used to find the maximum surge current for a square wave of any pulse width between 1 ms and 1000 ms by plottin g

the applicable points on logarithmic paper . Examples of this, using the 3.3 V and 200 V zener are shown in Figure 7. Mounting contact located

as specified in Note 2 (TA = 25°C +8°C, –2°C).

4. VOLTAGE REGULATION (VZ)

The conditions for voltage regulation are as follows: VZ measurements are made at 10% and then at 50% of the IZ max value listed in the

electrical characteristics table. The test current time duration for each VZ measurement is 40 ±10 ms. Mounting contact located as specified

in Note 2 (TA = 25°C +8°C, –2°C).

5. MAXIMUM REGULATOR CURRENT (IZM)

The maximum current shown is based on the maximum voltage of a 5% type unit, therefore, it applies only to the B–suffix device. The actual

IZM for any device may not exceed the value of 5 watts divided by the actual VZ of the device. TL = 75°C at 3/8″ maximum from the device

body.

*Not Available in the 2000/Ammo Pack.

1N5333B Series

http://onsemi.com

ELECTRICAL CHARACTERISTICS (TA = 25°C unless otherwise noted, VF = 1.2 V Max @ IF = 1.0 A for all types)

Zener Voltage (Note 7) Zener Impedance (Note 7) Leakage

Current

VZ

IZM

Device

VZ (Volts) @ IZT ZZT @ IZT ZZK @ IZK IZK IR @ VR

(Note 8)

V

(Note 9)

(Note 10)

(Note 6)

Marking Min Nom Max mA   AA Max Volts A Volts mA

1N5363B 1N5363B 28.5 30 31.5 40 8 140 1 0.5 22.8 3.7 0.6 158

1N5364B 1N5364B 31.35 33 34.65 40 10 150 1 0.5 25.1 3.5 0.6 144

1N5365B 1N5365B 34.2 36 37.8 30 11 160 1 0.5 27.4 3.5 0.65 132

1N5366B 1N5366B 37.05 39 40.95 30 14 170 1 0.5 29.7 3.1 0.65 122

1N5367B 1N5367B 40.85 43 45.15 30 20 190 1 0.5 32.7 2.8 0.7 110

1N5368B 1N5368B 44.65 47 49.35 25 25 210 1 0.5 35.8 2.7 0.8 100

1N5369B 1N5369B 48.45 51 53.55 25 27 230 1 0.5 38.8 2.5 0.9 93

1N5370B 1N5370B 53.2 56 58.8 20 35 280 1 0.5 42.6 2.3 1.0 86

1N5371B 1N5371B 57 60 63 20 40 350 1 0.5 45.5 2.2 1.2 79

1N5372B 1N5372B 58.9 62 65.1 20 42 400 1 0.5 47.1 2.1 1.35 76

1N5373B 1N5373B 64.6 68 71.4 20 44 500 1 0.5 51.7 2.0 1.52 70

1N5374B 1N5374B 71.25 75 78.75 20 45 620 1 0.5 56 1.9 1.6 63

1N5375B 1N5375B 77.9 82 86.1 15 65 720 1 0.5 62.2 1.8 1.8 58

1N5376B 1N5376B 82.65 87 91.35 15 75 760 1 0.5 66 1.7 2.0 54.5

1N5377B 1N5377B 86.45 91 95.55 15 75 760 1 0.5 69.2 1.6 2.2 52.5

1N5378B 1N5378B 95 100 105 12 90 800 1 0.5 76 1.5 2.5 47.5

1N5379B 1N5379B 104.5 110 115.5 12 125 1000 1 0.5 83.6 1.4 2.5 43

1N5380B 1N5380B 114 120 126 10 170 1150 1 0.5 91.2 1.3 2.5 39.5

1N5381B 1N5381B 123.5 130 136.5 10 190 1250 1 0.5 98.8 1.2 2.5 36.6

1N5382B 1N5382B 133 140 147 8 230 1500 1 0.5 106 1.2 2.5 34

1N5383B 1N5383B 142.5 150 157.5 8 330 1500 1 0.5 114 1.1 3.0 31.6

1N5384B 1N5384B 152 160 168 8 350 1650 1 0.5 122 1.1 3.0 29.4

1N5385B 1N5385B 161.5 170 178.5 8 380 1750 1 0.5 129 1.0 3.0 28

1N5386B 1N5386B 171 180 189 5 430 1750 1 0.5 137 1.0 4.0 26.4

1N5387B 1N5387B 180.5 190 199.5 5 450 1850 1 0.5 144 0.9 5.0 25

1N5388B 1N5388B 190 200 210 5 480 1850 1 0.5 152 0.9 5.0 23.6

6. TOLERANCE AND TYPE NUMBER DESIGNATION

The JEDEC type numbers shown indicate a tolerance of ±5%.

7. ZENER VOLTAGE (VZ) and IMPEDANCE (IZT and IZK)

Test conditions for zener voltage and impedance are as follows: IZ is applied 40 ±10 ms prior to reading. Mounting contacts are located 3/8″

to 1/2″ from the inside edge of mounting clips to the body of the diode (TA = 25°C +8°C, –2°C).

8. SURGE CURRENT (IR)

Surge current is specified as the maximum allowable peak, non–recurrent square–wave current with a pulse width, PW, of 8.3 ms. The data

given in Figure 6 may be used to find the maximum surge current for a square wave of any pulse width between 1 ms and 1000 ms by plottin g

the applicable points on logarithmic paper . Examples of this, using the 3.3 V and 200 V zener are shown in Figure 7. Mounting contact located

as specified in Note 7 (TA = 25°C +8°C, –2°C).

9. VOLTAGE REGULATION (VZ)

The conditions for voltage regulation are as follows: VZ measurements are made at 10% and then at 50% of the IZ max value listed in the

electrical characteristics table. The test current time duration for each VZ measurement is 40 ±10 ms. Mounting contact located as specified

in Note 7 (TA = 25°C +8°C, –2°C).

10.MAXIMUM REGULATOR CURRENT (IZM)

The maximum current shown is based on the maximum voltage of a 5% type unit, therefore, it applies only to the B–suffix device. The actual

IZM for any device may not exceed the value of 5 watts divided by the actual VZ of the device. TL = 75°C at 3/8″ maximum from the device

body.

1N5333B Series

http://onsemi.com

Figure 1. Power Temperature Derating Curve

TL, LEAD TEMPERATURE (°C)

PD, MAXIMUM STEADY STATE

POWER DISSIPATION (WATTS)

0 20 40 60 80 100 120 140 160 180 200

L=LEAD LENGTH

L=TO HEAT SINK

L=(SEE FIGURE 5)

L=1/8″

L=3/8″

L=1″

TEMPERATURE COEFFICIENTS

Figure 2. Temperature Coefficient-Range

for Units 3 to 10 Volts Figure 3. Temperature Coefficient-Range

for Units 10 to 220 Volts

VZ, ZENER VOLTAGE @ IZT (VOLTS)

-2

34 5678910

RANGE

300

200

100

0 20 40 60 80 100 120 140 160 180 200 220

VZ, ZENER VOLTAGE @ IZT (VOLTS)

θVZ, TEMPERATURE COEFFICIENT

(mV/°C) @ I ZT

θVZ, TEMPERATURE COEFFICIENT

(mV/°C) @ I ZT

RANGE

1N5333B Series

http://onsemi.com

Figure 4. Typical Thermal Response

L, Lead Length = 3/8 Inch

Figure 5. Typical Thermal Resistance Figure 6. Maximum Non-Repetitive Surge Current

versus Nominal Zener Voltage

(See Note 3)

θJL (t, D), TRANSIENT THERMAL RESISTANCE

JUNCTIONTOLEAD (°C/W)

0.5

0.2

0.00

0.01 0.05 0.1 0.5 1 5 10 20 50 100

D = 0.5

D = 0.2

D = 0.1

D = 0.05

D = 0.01

D = 0

NOTE: BELOW 0.1 SECOND, THERMAL

NOTE: RESPONSE CURVE IS APPLICABLE

NOTE: TO ANY LEAD LENGTH (L).

DUTY CYCLE, D = t1/t2

SINGLE PULSE  TJL = JL(t)PPK

REPETITIVE PULSES  TJL = JL(t, D)PPK

PPK t1

t, TIME (SECONDS)

00 0.2 0.4 0.6 0.8 1

PRIMARY PATH OF

CONDUCTION IS THROUGH

THE CATHODE LEAD

L L

L, LEAD LENGTH TO HEAT SINK (INCH)

, JUNCTIONTOLEAD THERMAL RESISTANCE (

θ°C/W)

Ir, PEAK SURGE CURRENT (AMPS)

0.1

0.2

0.4

34 6810 20 30 40 60 80 100 200

*SQUARE WAVE PW=100ms*

PW=1000ms*

PW=1ms*

PW=8.3ms*

NOMINAL VZ (V)

0.1

0.2

0.5

1 10 100 100

1000

100

0.1

1 234 5678 910

IZ, ZENER CURRENT (mA)

PW, PULSE WIDTH (ms) VZ, ZENER VOLTAGE (VOLTS)

Figure 7. Peak Surge Current versus Pulse Width

(See Note 3) Figure 8. Zener Voltage versus Zener Current

VZ= 3.3 thru 10 Volts

VZ=200V

VZ=3.3V

PLOTTED FROM INFORMATION

GIVEN IN FIGURE 6

TC=25°C

T=25°C

Ir, PEAK SURGE CURRENT (AMPS)

1N5333B Series

http://onsemi.com

IZ, ZENER CURRENT (mA)

VZ, ZENER VOLTAGE (VOLTS)

1000

100

0.1

10 20 30 40 50 60 70 80

100

0.1

80 100 120 140 160 180 200 220

VZ, ZENER VOLTAGE (VOLTS)

IZ, ZENER CURRENT (mA)

T=25°C

Figure 9. Zener Voltage versus Zener Current

VZ = 11 thru 75 Volts Figure 10. Zener Voltage versus Zener Current

VZ = 82 thru 200 Volts

APPLICATION NOTE

Since the actual voltage available from a given zener

diode is temperature dependent, it is necessary to determine

junction temperature under any set of operating conditions

in order to calculate its value. The following procedure is

recommended:

Lead Temperature, TL, should be determined from:

TL = LA PD + TA

LA is the lead-to-ambient thermal resistance and PD is the

power dissipation.

Junction Temperature, TJ, may be found from:

TJ = TL + TJL

TJL is the increase in junction temperature above the lead

temperature and may be found from Figure 4 for a train of

power pulses or from Figure 5 for dc power.

TJL = JL PD

For worst-case design, using expected limits of IZ, limits

of PD and the extremes of TJ (TJ) may be estimated.

Changes in voltage, VZ, can then be found from:

V = VZ TJ

VZ, the zener voltage temperature coefficient, is found

from Figures 2 and 3.

Under high power-pulse operation, the zener voltage will

vary with time and may also be affected significantly by the

zener resistance. For best regulation, keep current

excursions as low as possible.

Data of Figure 4 should not be used to compute surge

capability. Sur ge limitations are given in Figure 6. They are

lower than would be expected by considering only junction

temperature, as current crowding effects cause temperatures

to be extremely high in small spots resulting in device

degradation should the limits of Figure 6 be exceeded.

1N5333B Series

http://onsemi.com

OUTLINE DIMENSIONS

5 Watt DO–41 Surmetic 40

Zener Voltage Regulators – Axial Leaded

AXIAL LEAD

CASE 17–02

ISSUE C

DIM MIN MAX MIN MAX

MILLIMETERSINCHES

A0.330 0.350 8.38 8.89

B0.130 0.145 3.30 3.68

D0.037 0.043 0.94 1.09

F--- 0.050 --- 1.27

K1.000 1.250 25.40 31.75

NOTES:

1. LEAD DIAMETER AND FINISH NOT CONTROLLED

WITHIN DIMENSION F.

STYLE 1:

PIN 1. ANODE

2. CATHODE

ON Semiconductor and are registered trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC reserves the right to make

changes without further notice to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any

particular purpose, nor does SCILLC assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all

liability, including without limitation special, consequential or incidental damages. “Typical” parameters which may be provided in SCILLC data sheets and/or

specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including “Typicals” must be

validated for each customer application by customer’s technical experts. SCILLC does not convey any license under its patent rights nor the rights of others.

SCILLC products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications

intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where personal injury or death

may occur. Should Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC

and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees

arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that

SCILLC was negligent regarding the design or manufacture of the part. SCILLC is an Equal Opportunity/Affirmative Action Employer.

PUBLICATION ORDERING INFORMATION

JAPAN: ON Semiconductor, Japan Customer Focus Center

4–32–1 Nishi–Gotanda, Shinagawa–ku, Tokyo, Japan 141–0031

Phone: 81–3–5740–2700

Email: r14525@onsemi.com

ON Semiconductor Website: http://onsemi.com

For additional information, please contact your local

Sales Representative.

1N5333B/D

Surmetic is a trademark of Semiconductor Components Industries, LLC.

Literature Fulfillment:

Literature Distribution Center for ON Semiconductor

P.O. Box 5163, Denver, Colorado 80217 USA

Phone: 303–675–2175 or 800–344–3860 Toll Free USA/Canada

Fax: 303–675–2176 or 800–344–3867 Toll Free USA/Canada

Email: ONlit@hibbertco.com

N. American Technical Support: 800–282–9855 Toll Free USA/Canada