EE-SPX-W Slot-type Photomicrosensor with Cable 47
Slot-type Photomicrosensor with Cable
EE-SPX-W
Photomicrosensor with built-in
amplifier and attached cable reduces
external light interference.
■Light modulation effectively reduces external light
interference.
■Wide operation voltage range: 5 to 24 VDC
■Easy operation monitoring with bright light indicator.
Refer to Precautions on page 49.
Ordering Information
Note: The EE-SPX305-W2A/SPX405-W2A are not CE certified due to their internal structures. All other Photomicrosensors are CE certified.
Appearance Sensing
method
Sensing distance
(slot width)
Output
type
Output
configuration
Cable
length Model
Through-beam
type
NPN
output
Dark-ON
1 m
EE-SPX302-W2A
Light-ON EE-SPX402-W2A
Dark-ON EE-SPX304-W2A
Light-ON EE-SPX404-W2A
Dark-ON EE-SPX306-W2A
Light-ON EE-SPX406-W2A
Dark-ON EE-SPX305-W2A
(See note.)
Light-ON EE-SPX405-W2A
(See note.)
Infrared li
g
ht
3.6 mm
3.6 mm
3.6 mm
5.0 mm
48 EE-SPX-W Slot-type Photomicrosensor with Cable
Ratings/Characteristics
I/O Circuits
NPN Output
Item Models
EE-SPX302-W2A, EE-SPX402-W2A
EE-SPX304-W2A, EE-SPX404-W2A
EE-SPX306-W2A, EE-SPX406-W2A
EE-SPX305-W2A
EE-SPX405-W2A
Sensing distance 3.6 mm (slot width) 5 mm (slot width) ∗1. The indicator is a GaP red LED
(peak emission wavelength: 700 nm).
∗2. The response frequency was measured by
detecting the following rotating disk.
Sensing object Opaque: 1 × 0.5 mm min. Opaque: 2 × 0.8 mm min.
Differential distance 0.05 mm max.
Light source GaAs infrared LED (pulse lighting) with a peak wavelength of
940 nm
Indicator ∗1Light indicator (red)
Supply voltage 5 to 24 VDC ±10%, ripple (p-p): 5% max.
Current consumption Average: 15 mA max.; Peak: 50 mA max.
Control output
NPN voltage output:
Load power supply voltage: 5 to 24 VDC
Load current: 80 mA max.
80 mA load current with a residual voltage of 1.0 V max.
10 mA load current with a residual voltage of 0.4 V max.
Response frequency
∗2500 Hz min.
Ambient illumination 3,000 lx max. with incandescent light or sunlight on the surface of
the receiver
Ambient temperature Operating: −10 to +55°C
Storage: −25 to +65°C
Ambient humidity Operating: 5% to 85%
Storage: 5% to 95%
Vibration resistance Destruction: 10 to 55 Hz, 1.5-mm double amplitude for 2 h each
in X, Y, and Z directions
Shock resistance Destruction: 500 m/s2 for 3 times each in X, Y, and Z directions
Enclosure rating IEC IP50
Connecting method Pre-wired (standard cable length: 1 m)
Weight 18.5 g
Material Case Polycarbonate
Holder
Model Output
configuration Timing charts Output circuit
EE-SPX402-W2A
EE-SPX404-W2A
EE-SPX405-W2A
EE-SPX406-W2A
Light-ON
EE-SPX302-W2A
EE-SPX304-W2A
EE-SPX305-W2A
EE-SPX306-W2A
Dark-ON
2 mm
2 mm
2 mm
Disk
Disk
Disk
EE-SPX305-W2A
EE-SPX302-W2A EE-SPX306-W2A
Incident
Interrupted
ON
OFF
ON
OFF
Operates
Releases
H
L
Light indicator
(red)
Output
transistor
Load 1
(relay)
Load 2
5 to 24 VD
C
Light indicator (red)
1.5 to
3 mA Load 1
Load 2
Main
circuit
Black
Blue
Brown
∗
∗ Voltage output (when the sensor is connected to a transistor circuit)
Incident
Interrupted
ON
OFF
ON
OFF
Operates
Releases
H
L
Light indicator
(red)
Output
transistor
Load 1
(relay)
Load 2
EE-SPX-W Slot-type Photomicrosensor with Cable 49
Engineering Data
Precautions
Refer to General Precautions on page 23 to 28 for general precautions.
Do not use this product in sensing devices
designed to provide human safety.
Make sure that this product is used within the rated ambient
environment conditions.
● Wiring
•When extending the cable, use an extension cable with
conductors having a total cross-section area of 0.3 mm2.
The total cable length must be 2 m maximum.
•To use a cable length longer than 2 m, attach a capacitor
with a capacitance of approximately 10 µF to the wires as
shown below. The distance between the terminal and the
capacitor must be within 2 m. (Use a capacitor with a
dielectric strength that is at least twice the Sensor's power
supply voltage.)
Sensing Position Characteristics
(Typical)
EE-SPX302-W2A
EE-SPX304-W2A
EE-SPX306-W2A
EE-SPX302-W2A
EE-SPX304-W2A
EE-SPX306-W2A
EE-SPX305-W2A EE-SPX305-W2A
0123456
Tr ON
Tr OFF
d
d
Dark-ON
Distance d (mm)
0123456
Tr ON
Tr OFF
d
Dark-ON
Distance d (mm)
Tr ON
Tr OFF
0123456
EE-SPX305-W2A
d
Dark-ON
Distance d
(
mm
)
Tr ON
Tr OFF
d
Dark-ON
012345
6
Distance d
(
mm
)
Warning Precautions for Correct Use
+
−
A capacitance of
10 µF min.
5 to 24 VDC
2 m max.
0 V
+
−
Extension cable
50 EE-SPX-W Slot-type Photomicrosensor with Cable
Dimensions (Unit: mm)
∗
Optical axis
(0.5-mm wide) Optical axis
(1-mm wide)
See note.
2.5
2.5
13 3.6
C0.5
2 dia.
6.6 Indicator window
R3.2
R3.2
7 dia.
6
7
15.6 3 3.5 dia.
hole
6.5
21.2 8
1,000
∗ Vinyl-insulated round cable of 3.5 dia., 3 cores,
(0.14 mm2 with 1.0-dia. insulator); Standard length: 1 m
Note: The lug is used to prevent turning and to indicate the optical axis.
When installin
g
, make a fixed hole of 2.1 to 2.3 mm dia.
EE-SPX302-W2A
EE-SPX402-W2A
∗
Optical axis
(0.5-mm wide)
Optical axis (1-mm wide)
See note.
2.5
2.5
13 3.6
C0.5
2 dia.
6.6 Indicator window
R3.2
R3.2
7 dia.
6
6
7
15.6 3 3.5 dia.
hole
6.5
21.2 8
1,000
Note: The lug is used to prevent turning and to indicate the optical axis.
When installing, make a fixed hole of 2.1 to 2.3 mm dia.
∗ Vinyl-insulated round cable of 3.5 dia., 3 cores,
(0.14 mm2 with 1.0-dia. insulator); Standard length: 1
m
EE-
S
PX304-W2A
EE-SPX404-W2A
3.6
6.6 Two, 3.5 dia. holes
Optical axis
(0.5-mm wide)
7.4
7
1.5 max.
Indicator window
68
21.2 1,000
Optical axis
(1-mm wide)
15.6 3
13.8 19 25
∗
∗ Vinyl-insulated round cable of 3.5 dia., 3 cores,
(
0.14 mm2 with 1.0-dia. insulator
)
; Standard len
g
th: 1 m
Indicator
window
EE-
S
PX306-W2A
EE-SPX406-W2A
∗
14.5 1,000
8
6.95
7.2
12.7
15.5
6.35 Optical axis window (2 × 0.8)
3.6 3.2
9
20
Two, 3.2 dia.
14.4 20 27.2
5
Four, R2
Indicator window
∗ Vinyl-insulated round cable of 3.5 dia., 3 cores,
(0.14 mm2 with 1.0-dia. insulator); Standard length: 1 m
7 dia.
EE-
S
PX305-W2A
EE-SPX405-W2A
