LBA126L Dual Single-Pole OptoMOS(R) Relay INTEGRATED CIRCUITS DIVISION Parameter Blocking Voltage Load Current On-Resistance (max) Ratings 250 150 20 Units VP mArms / mADC Features * Current Limited * 3750Vrms Input/Output Isolation * Low Drive Power Requirements (TTL/CMOS Compatible) * High Reliability * Arc-Free With No Snubbing Circuits * No EMI/RFI Generation * Small 8-Pin Package * Machine Insertable, Wave Solderable * Surface Mount, Tape & Reel Version Available Description LBA126L comprises two independent 250V, 150mA, 20 solid state relays: one single-pole, normally open (1-Form-A), current limited relay and one single-pole, normally closed (1-Form-B) relay. The device employs optically coupled MOSFET technology to provide 3750Vrms of input/output isolation. Its optically coupled outputs, efficient MOSFET switches which use IXYS Integrated Circuits Division's patented OptoMOS architecture, are controlled by a highly efficient GaAIAs infrared LED. LBA126L is designed to provide an ideal solution where a complementary Form-A/Form-B relay pair is required in a space-saving single package. Approvals Applications * Telecommunications * Telecom Switching * Tip/Ring Circuits * Modem Switching (Laptop, Notebook, Pocket Size) * Hook Switch * Dial Pulsing * Ground Start * Ringing Injection * Instrumentation * Multiplexers * Data Acquisition * Electronic Switching * I/O Subsystems * Meters (Watt-Hour, Water, Gas) * Medical Equipment-Patient/Equipment Isolation * Security * Aerospace * Industrial Controls * UL Recognized Component: File E76270 * CSA Certified Component: Certificate 1175739 * EN/IEC 60950-1 Certified Component: TUV Certificate B 09 07 49410 004 Ordering Information Part # LBA126L LBA126LS LBA126LSTR Description 8-Pin DIP (50/Tube) 8-Pin Surface Mount (50/Tube) 8-Pin Surface Mount (1,000/Reel) Pin Configuration AC/DC Configuration + Control - Normally Closed - Control - Normally Closed + Control - Normally Open - Control - Normally Open 1 8 2 7 3 6 4 5 Switching Characteristics of Normally Open Devices Switching Characteristics of Normally Closed Devices IF IF ILOAD 90% ILOAD ton DS-LBA126L-R04 Normally Open Pole Form-B Form-A Pb Normally Closed Pole 90% 10% 10% toff toff ton e3 www.ixysic.com 1 INTEGRATED CIRCUITS DIVISION LBA126L Absolute Maximum Ratings @ 25C Parameter Blocking Voltage Reverse Input Voltage Input Control Current Peak (10ms) Input Power Dissipation 1 Total Power Dissipation 2 Isolation Voltage, Input to Output Operational Temperature Storage Temperature 1 2 Ratings 250 5 50 1 150 800 3750 -40 to +85 -40 to +125 Absolute Maximum Ratings are stress ratings. Stresses in excess of these ratings can cause permanent damage to the device. Functional operation of the device at conditions beyond those indicated in the operational sections of this data sheet is not implied. Units VP V mA A mW mW Vrms C C Derate linearly 1.33 mW / C Derate linearly 6.67 mW / C Electrical Characteristics @ 25C Parameter Output Characteristics Load Current Continuous 1 Peak On-Resistance Off-State Leakage Current Switching Speeds Turn-On Turn-Off Output Capacitance Load Current Limiting Input Characteristics Input Control Current to Activate Input Control Current to Deactivate Input Voltage Drop Reverse Input Current Common Characteristics Input to Output Capacitance 1 2 Conditions Symbol Min Typ Max Units t = 10ms IL=150mA VL=250VP IL ILPK RON ILEAK - - 150 400 20 1 mArms / mADC mAP VL=50V, f=1MHz - ton toff COUT ICL 170 50 235 5 5 280 pF mA IL=150mA IF=5mA VR=5V IF VF IR 0.4 0.9 - 0.7 1.2 - 5 1.4 10 mA mA V A - CI/O - 3 - pF IF=5mA, VL=10V A ms If both poles operate the load current must be derated so as not to exceed the package power dissipation value. www.ixysic.com R04 INTEGRATED CIRCUITS DIVISION LBA126L Manufacturing Information Moisture Sensitivity All plastic encapsulated semiconductor packages are susceptible to moisture ingression. IXYS Integrated Circuits Division classified all of its plastic encapsulated devices for moisture sensitivity according to the latest version of the joint industry standard, IPC/JEDEC J-STD-020, in force at the time of product evaluation. We test all of our products to the maximum conditions set forth in the standard, and guarantee proper operation of our devices when handled according to the limitations and information in that standard as well as to any limitations set forth in the information or standards referenced below. Failure to adhere to the warnings or limitations as established by the listed specifications could result in reduced product performance, reduction of operable life, and/or reduction of overall reliability. This product carries a Moisture Sensitivity Level (MSL) rating as shown below, and should be handled according to the requirements of the latest version of the joint industry standard IPC/JEDEC J-STD-033. Device Moisture Sensitivity Level (MSL) Rating LBA126L / LBA126LS MSL 1 ESD Sensitivity This product is ESD Sensitive, and should be handled according to the industry standard JESD-625. Reflow Profile This product has a maximum body temperature and time rating as shown below. All other guidelines of J-STD-020 must be observed. Device Maximum Temperature x Time LBA126L / LBA126LS 250C for 30 seconds Board Wash IXYS Integrated Circuits Division recommends the use of no-clean flux formulations. However, board washing to remove flux residue is acceptable. Since IXYS Integrated Circuits Division employs the use of silicone coating as an optical waveguide in many of its optically isolated products, the use of a short drying bake could be necessary if a wash is used after solder reflow processes. Chlorine- or Fluorine-based solvents or fluxes should not be used. Cleaning methods that employ ultrasonic energy should not be used. Pb R04 e3 www.ixysic.com 3 INTEGRATED CIRCUITS DIVISION LBA126L MECHANICAL DIMENSIONS LBA126L 2.540 0.127 (0.100 0.005) 9.652 0.381 (0.380 0.015) 8-0.800 DIA. (8-0.031 DIA.) 2.540 0.127 (0.100 0.005) 9.144 0.508 (0.360 0.020) 6.350 0.127 (0.250 0.005) Pin 1 PCB Hole Pattern 7.620 0.254 (0.300 0.010) 6.350 0.127 (0.250 0.005) 0.457 0.076 (0.018 0.003) 3.302 0.051 (0.130 0.002) 7.620 0.127 (0.300 0.005) 7.239 TYP. (0.285) 4.064 TYP (0.160) 0.254 0.0127 (0.010 0.0005) 7.620 0.127 (0.300 0.005) Dimensions mm (inches) 0.813 0.102 (0.032 0.004) LBA126LS 9.652 0.381 (0.380 0.015) 2.540 0.127 (0.100 0.005) 6.350 0.127 (0.250 0.005) Pin 1 0.635 0.127 (0.025 0.005) 3.302 0.051 (0.130 0.002) 9.525 0.254 (0.375 0.010) 0.457 0.076 (0.018 0.003) PCB Land Pattern 2.54 (0.10) 8.90 (0.3503) 1.65 (0.0649) 7.620 0.254 (0.300 0.010) 0.254 0.0127 (0.010 0.0005) 0.65 (0.0255) 4.445 0.127 (0.175 0.005) Dimensions mm (inches) 0.813 0.102 (0.032 0.004) 4 www.ixysic.com R04 INTEGRATED CIRCUITS DIVISION LBA126L LBA126LSTR Tape & Reel 330.2 DIA. (13.00 DIA.) Top Cover Tape Thickness 0.102 MAX. (0.004 MAX.) K0 =4.90 (0.193) K1 =4.20 (0.165) Embossed Carrier Embossment W=16.00 (0.63) Bo=10.30 (0.406) Ao=10.30 (0.406) P=12.00 (0.472) User Direction of Feed Dimensions mm (inches) NOTES: 1. Dimensions carry tolerances of EIA Standard 481-2 2. Tape complies with all "Notes" for constant dimensions listed on page 5 of EIA-481-2 For additional information please visit our website at: www.ixysic.com IXYS Integrated Circuits Division makes no representations or warranties with respect to the accuracy or completeness of the contents of this publication and reserves the right to make changes to specifications and product descriptions at any time without notice. Neither circuit patent licenses nor indemnity are expressed or implied. Except as set forth in IXYS Integrated Circuits Division's Standard Terms and Conditions of Sale, IXYS Integrated Circuits Division assumes no liability whatsoever, and disclaims any express or implied warranty, relating to its products including, but not limited to, the implied warranty of merchantability, fitness for a particular purpose, or infringement of any intellectual property right. The products described in this document are not designed, intended, authorized or warranted for use as components in systems intended for surgical implant into the body, or in other applications intended to support or sustain life, or where malfunction of IXYS Integrated Circuits Division's product may result in direct physical harm, injury, or death to a person or severe property or environmental damage. IXYS Integrated Circuits Division reserves the right to discontinue or make changes to its products at any time without notice. 5 Specification: DS-LBA126L-R04 (c)Copyright 2012, IXYS Integrated Circuits Division OptoMOS(R) is a registered trademark of IXYS Integrated Circuits Division All rights reserved. Printed in USA. 12/22/2012