Customer Drawing 2.7 Gb/s 12-ch Parallel Fiber Transmitter and Receiver ZL60101MLDL, ZL60102MLDL November 2010 Description The ZL60101 and ZL60102 together make a high speed transmitter/receiver pair for parallel fiber applications. Features * 12 parallel channels, total 32.6 Gbps capacity * Data rate up to 2.72 Gbps per channel * 850 nm VCSEL array * Link reach 300 m with 50/125m 500 MHz.km fiber at 2.5 Gbps * Channel BER better than 10-12 * Industry standard MPO/MTPTM ribbon fiber connector interface * Pluggable MegArray(R) ball grid array connector * Laser class 1M IEC 60825-1:2001 compliant * Power supply 3.3 V * Compatible with industry MSA Applications * High-speed interconnects within and between switches, routers and transport equipment * Low cost SONET/SDH VSR (Very Short Reach) OC-192/STM64 connections * InfiniBand(R) connections * Interconnects rack-to-rack, shelf-to-shelf, board-to-board, board-to-optical backplane Tyco Electronics Nederland B.V. All international rights reserved Tyco Electronics The ZL60101 transmitter module converts parallel electrical input signals via a laser driver and a VCSEL array into parallel optical output signals at a wavelength of 850 nm. The ZL60102 receiver module converts parallel optical input signals via a PIN photodiode array and a transimpedance and limiting amplifier into electrical output signals. The modules are pluggable each fitted with an industry standard MegArray(R) BGA connector. This provides ease of assembly on the host board and enables provisioning of bandwidth on demand. Reliability assurance is based on Telcordia GR-468-CORE and the parts are compliant to the EU directive 2002/95/EC issued 27 January 2003 [RoHS]. This information is confidential and propriety to Tyco Electronics and its worldwide subsidiaries and affiliates. It may not be disclosed to anyone, other than Tyco Electronics personnel, without written authorization from Tyco Electronics Corporation, Harisburg, Pennsylvania USA This specification is a controlled document and subject to change. Contact the Engineering Control Organization for the latest revision. *Trademark R6-76 (Rev. 03-07) 1 of 17 Customer Drawing 2.7 Gb/s 12-ch Parallel Fiber Transmitter and Receiver ZL60101MLDL, ZL60102MLDL November 2010 Table of Contents Features .......................................................................................................................................... 1 Applications ................................................................................................................................... 1 Description ...................................................................................................................................... 1 Absolute Maximum Ratings .......................................................................................................... 3 Recommended Operating Conditions .......................................................................................... 3 ZL60101 Transmitter Specifications ............................................................................................. 4 Transmitter Control and Status Signals ............................................................................... 6 Transmitter Control and Status Timing Diagrams ............................................................... 7 Transmitter Pin out Assignments......................................................................................... 9 Transmitter Pin Description ...............................................................................................10 ZL60102 Receiver Specifications ................................................................................................11 Receiver Control and Status Signals .................................................................................12 Receiver Control and Status Timing Diagrams .................................................................13 Receiver Pin out Assignments...........................................................................................14 Receiver Pin Description ...................................................................................................15 Handling instructions ...................................................................................................................16 Cleaning the Optical Interface ...........................................................................................16 Connectors ........................................................................................................................16 ESD Handling ....................................................................................................................16 Link Reach.....................................................................................................................................17 Link Model Parameters ......................................................................................................17 Trademarks ...................................................................................................................................17 Tyco Electronics Nederland B.V. All international rights reserved Tyco Electronics This information is confidential and propriety to Tyco Electronics and its worldwide subsidiaries and affiliates. It may not be disclosed to anyone, other than Tyco Electronics personnel, without written authorization from Tyco Electronics Corporation, Harisburg, Pennsylvania USA This specification is a controlled document and subject to change. Contact the Engineering Control Organization for the latest revision. *Trademark R6-76 (Rev. 03-07) 2 of 17 Customer Drawing 2.7 Gb/s 12-ch Parallel Fiber Transmitter and Receiver ZL60101MLDL, ZL60102MLDL November 2010 Absolute Maximum Ratings Not necessarily applied together. Exceeding these values may cause permanent damage. Functional operation under these conditions is not implied. Recommended Operating Conditions These parameters apply both to the transmitter and the receiver. Figure 1 - Recommended Power Supply Filter Tyco Electronics Nederland B.V. All international rights reserved Tyco Electronics This information is confidential and propriety to Tyco Electronics and its worldwide subsidiaries and affiliates. It may not be disclosed to anyone, other than Tyco Electronics personnel, without written authorization from Tyco Electronics Corporation, Harisburg, Pennsylvania USA This specification is a controlled document and subject to change. Contact the Engineering Control Organization for the latest revision. *Trademark R6-76 (Rev. 03-07) 3 of 17 Customer Drawing 2.7 Gb/s 12-ch Parallel Fiber Transmitter and Receiver ZL60101MLDL, ZL60102MLDL November 2010 ZL60101 Transmitter Specifications All parameters below require operating conditions according to "Recommended Operating Conditions" on page 3. Tyco Electronics Nederland B.V. All international rights reserved Tyco Electronics This information is confidential and propriety to Tyco Electronics and its worldwide subsidiaries and affiliates. It may not be disclosed to anyone, other than Tyco Electronics personnel, without written authorization from Tyco Electronics Corporation, Harisburg, Pennsylvania USA This specification is a controlled document and subject to change. Contact the Engineering Control Organization for the latest revision. *Trademark R6-76 (Rev. 03-07) 4 of 17 Customer Drawing 2.7 Gb/s 12-ch Parallel Fiber Transmitter and Receiver ZL60101MLDL, ZL60102MLDL November 2010 Classified in accordance with IEC 60825-1/A2:2001, IEC 60825-2 : 2000 Class 1M Laser Product Emitted wavelength: 840 nm Figure 2 - ZL60101 Transmitter Block Diagram Table 1 - Transmitter Optical Channel Assignment Tyco Electronics Nederland B.V. All international rights reserved Tyco Electronics This information is confidential and propriety to Tyco Electronics and its worldwide subsidiaries and affiliates. It may not be disclosed to anyone, other than Tyco Electronics personnel, without written authorization from Tyco Electronics Corporation, Harisburg, Pennsylvania USA This specification is a controlled document and subject to change. Contact the Engineering Control Organization for the latest revision. *Trademark R6-76 (Rev. 03-07) 5 of 17 Customer Drawing 2.7 Gb/s 12-ch Parallel Fiber Transmitter and Receiver ZL60101MLDL, ZL60102MLDL November 2010 Transmitter Control and Status Signals The following table shows the timing relationships of the status and control signals of the pluggable optical transmitter. Tyco Electronics Nederland B.V. All international rights reserved Tyco Electronics This information is confidential and propriety to Tyco Electronics and its worldwide subsidiaries and affiliates. It may not be disclosed to anyone, other than Tyco Electronics personnel, without written authorization from Tyco Electronics Corporation, Harisburg, Pennsylvania USA This specification is a controlled document and subject to change. Contact the Engineering Control Organization for the latest revision. *Trademark R6-76 (Rev. 03-07) 6 of 17 Customer Drawing 2.7 Gb/s 12-ch Parallel Fiber Transmitter and Receiver ZL60101MLDL, ZL60102MLDL November 2010 Transmitter Control and Status Timing Diagrams The following figures show the timing relationships of the status and control signals of the pluggable optical transmitter. Figure 3 - Transmitter Power-up Sequence. Figure 4 - Transmitter Fault Signal Timing Diagram Tyco Electronics Nederland B.V. All international rights reserved Tyco Electronics This information is confidential and propriety to Tyco Electronics and its worldwide subsidiaries and affiliates. It may not be disclosed to anyone, other than Tyco Electronics personnel, without written authorization from Tyco Electronics Corporation, Harisburg, Pennsylvania USA This specification is a controlled document and subject to change. Contact the Engineering Control Organization for the latest revision. *Trademark R6-76 (Rev. 03-07) 7 of 17 Customer Drawing 2.7 Gb/s 12-ch Parallel Fiber Transmitter and Receiver ZL60101MLDL, ZL60102MLDL November 2010 Figure 5 - Transmitter Reset Signal Timing Diagram Figure 6 - Transmitter Enable and Disable Timing Diagram Table 2 - Truth Table for Transmitter Operation (Pre-condition: RESET floating or HIGH) Tyco Electronics Nederland B.V. All international rights reserved Tyco Electronics This information is confidential and propriety to Tyco Electronics and its worldwide subsidiaries and affiliates. It may not be disclosed to anyone, other than Tyco Electronics personnel, without written authorization from Tyco Electronics Corporation, Harisburg, Pennsylvania USA This specification is a controlled document and subject to change. Contact the Engineering Control Organization for the latest revision. *Trademark R6-76 (Rev. 03-07) 8 of 17 Customer Drawing 2.7 Gb/s 12-ch Parallel Fiber Transmitter and Receiver ZL60101MLDL, ZL60102MLDL November 2010 Transmitter Pin out Assignments Table 3 - Transmitter Host Circuit Board Layout (Top view, toward MPO/MTPTM connector end) (10x10 array, 1.27 mm pitch) Tyco Electronics Nederland B.V. All international rights reserved Tyco Electronics This information is confidential and propriety to Tyco Electronics and its worldwide subsidiaries and affiliates. It may not be disclosed to anyone, other than Tyco Electronics personnel, without written authorization from Tyco Electronics Corporation, Harisburg, Pennsylvania USA This specification is a controlled document and subject to change. Contact the Engineering Control Organization for the latest revision. *Trademark R6-76 (Rev. 03-07) 9 of 17 Customer Drawing 2.7 Gb/s 12-ch Parallel Fiber Transmitter and Receiver ZL60101MLDL, ZL60102MLDL November 2010 Transmitter Pin Description Tyco Electronics Nederland B.V. All international rights reserved Tyco Electronics This information is confidential and propriety to Tyco Electronics and its worldwide subsidiaries and affiliates. It may not be disclosed to anyone, other than Tyco Electronics personnel, without written authorization from Tyco Electronics Corporation, Harisburg, Pennsylvania USA This specification is a controlled document and subject to change. Contact the Engineering Control Organization for the latest revision. *Trademark R6-76 (Rev. 03-07) 10 of 17 Customer Drawing 2.7 Gb/s 12-ch Parallel Fiber Transmitter and Receiver ZL60101MLDL, ZL60102MLDL November 2010 ZL60102 Receiver Specifications All parameters below require operating conditions according to "Recommended Operating Conditions," on page 3 and a termination load of 100 differential at the electrical output. Tyco Electronics Nederland B.V. All international rights reserved Tyco Electronics This information is confidential and propriety to Tyco Electronics and its worldwide subsidiaries and affiliates. It may not be disclosed to anyone, other than Tyco Electronics personnel, without written authorization from Tyco Electronics Corporation, Harisburg, Pennsylvania USA This specification is a controlled document and subject to change. Contact the Engineering Control Organization for the latest revision. *Trademark R6-76 (Rev. 03-07) 11 of 17 Customer Drawing 2.7 Gb/s 12-ch Parallel Fiber Transmitter and Receiver ZL60101MLDL, ZL60102MLDL November 2010 Figure 7 - ZL60102 Receiver Block Diagram Table 4 - Receiver Optical Channel Assignment Receiver Control and Status Signals The following table shows the timing relationships of the status and control signals of the pluggable optical receiver. Tyco Electronics Nederland B.V. All international rights reserved Tyco Electronics This information is confidential and propriety to Tyco Electronics and its worldwide subsidiaries and affiliates. It may not be disclosed to anyone, other than Tyco Electronics personnel, without written authorization from Tyco Electronics Corporation, Harisburg, Pennsylvania USA This specification is a controlled document and subject to change. Contact the Engineering Control Organization for the latest revision. *Trademark R6-76 (Rev. 03-07) 12 of 17 Customer Drawing 2.7 Gb/s 12-ch Parallel Fiber Transmitter and Receiver ZL60101MLDL, ZL60102MLDL November 2010 Receiver Control and Status Timing Diagrams The following figures show the timing relationships of the status and control signals of the pluggable optical receiver. Figure 8 - Receiver Enable Signal Timing Diagram Figure 9 - Receiver Signal Detect Timing Diagram Tyco Electronics Nederland B.V. All international rights reserved Tyco Electronics This information is confidential and propriety to Tyco Electronics and its worldwide subsidiaries and affiliates. It may not be disclosed to anyone, other than Tyco Electronics personnel, without written authorization from Tyco Electronics Corporation, Harisburg, Pennsylvania USA This specification is a controlled document and subject to change. Contact the Engineering Control Organization for the latest revision. *Trademark R6-76 (Rev. 03-07) 13 of 17 Customer Drawing 2.7 Gb/s 12-ch Parallel Fiber Transmitter and Receiver ZL60101MLDL, ZL60102MLDL November 2010 Receiver Pin out Assignments Table 5 - Receiver Pin out Assignments (Top view, toward MPO/MTPTM connector end) (10x10 array, 1.27 mm pitch) Tyco Electronics Nederland B.V. All international rights reserved Tyco Electronics This information is confidential and propriety to Tyco Electronics and its worldwide subsidiaries and affiliates. It may not be disclosed to anyone, other than Tyco Electronics personnel, without written authorization from Tyco Electronics Corporation, Harisburg, Pennsylvania USA This specification is a controlled document and subject to change. Contact the Engineering Control Organization for the latest revision. *Trademark R6-76 (Rev. 03-07) 14 of 17 Customer Drawing 2.7 Gb/s 12-ch Parallel Fiber Transmitter and Receiver ZL60101MLDL, ZL60102MLDL November 2010 Receiver Pin Description Tyco Electronics Nederland B.V. All international rights reserved Tyco Electronics This information is confidential and propriety to Tyco Electronics and its worldwide subsidiaries and affiliates. It may not be disclosed to anyone, other than Tyco Electronics personnel, without written authorization from Tyco Electronics Corporation, Harisburg, Pennsylvania USA This specification is a controlled document and subject to change. Contact the Engineering Control Organization for the latest revision. *Trademark R6-76 (Rev. 03-07) 15 of 17 Customer Drawing 2.7 Gb/s 12-ch Parallel Fiber Transmitter and Receiver ZL60101MLDL, ZL60102MLDL November 2010 Handling instructions Cleaning the Optical Interface A protective connector plug is supplied with each module. This plug should remain in place whenever a fiber cable is not inserted. This will keep the optical port free from dust or other contaminants, which may potentially degrade the optical signal. Before reattaching the connector plug to the module, visually inspect the plug and remove any contamination. If the module's optical port becomes contaminated, it can be cleaned with high-pressure nitrogen (the use of fluids, or physical contact, is not advised due to potential for damage). Before a fiber cable connector is attached to the module, it is recommended to clean the fiber cable connector using an optical connector cleaner, or according to the cable manufacturer's instructions. It is also recommended to clean the optical port of the module with high-pressure nitrogen. Connectors For optimum performance, it is recommended that the number of insertions is limited to 50 for the electrical MegArray connector and 200 for the optical MPO/MTP connector. ESD Handling When handling the modules, precautions for ESD sensitive devices should be taken. These include use of ESD protected work areas with wrist straps, controlled work-benches, floors etc. Tyco Electronics Nederland B.V. All international rights reserved Tyco Electronics This information is confidential and propriety to Tyco Electronics and its worldwide subsidiaries and affiliates. It may not be disclosed to anyone, other than Tyco Electronics personnel, without written authorization from Tyco Electronics Corporation, Harisburg, Pennsylvania USA This specification is a controlled document and subject to change. Contact the Engineering Control Organization for the latest revision. *Trademark R6-76 (Rev. 03-07) 16 of 17 Customer Drawing 2.7 Gb/s 12-ch Parallel Fiber Transmitter and Receiver ZL60101MLDL, ZL60102MLDL November 2010 Link Reach The following table lists the minimum reach distance of the 12 channel pluggable optical modules for different multimode fiber (MMF) types and bandwidths assuming worst case parameters. Each case allows for a maximum of 2 dB per channel connection loss for patch cables and other connectors. Table 6 - Link Reach for Different Fiber Types and Data Rates Longer operating distance than the range specified here can be achieved using transmitters, receivers and / or cables meeting specification but performing better than worst case. Link Model Parameters The link reaches above have been calculated using the following link model parameters and Gigabit Ethernet link model version 2.3.5 (filename: 5pmd047.xls). Trademarks Infiniband is a registered trademark of the InfiniBand Trade Association. MTP is a registered trademark of US Conec Ltd. The MegArray is a registered trademark of FCI. Tyco Electronics Nederland B.V. All international rights reserved Tyco Electronics This information is confidential and propriety to Tyco Electronics and its worldwide subsidiaries and affiliates. It may not be disclosed to anyone, other than Tyco Electronics personnel, without written authorization from Tyco Electronics Corporation, Harisburg, Pennsylvania USA This specification is a controlled document and subject to change. Contact the Engineering Control Organization for the latest revision. *Trademark R6-76 (Rev. 03-07) 17 of 17