© Semiconductor Components Industries, LLC, 2005
November, 2005 − Rev. 7 1Publication Order Number:
UC3842B/D
UC3842B, UC3843B,
UC2842B, UC2843B,
NCV3843BV
High Performance Current
Mode Controllers
The UC3842B, UC3843B series are high performance fixed
frequency current mode controllers. They are specifically designed for
Off−Line and DC−DC converter applications offering the designer a
cost−effective solution with minimal external components. These
integrated circuits feature a trimmed oscillator for precise duty cycle
control, a temperature compensated reference, high gain error
amplifier, current sensing comparator, and a high current totem pole
output ideally suited for driving a power MOSFET.
Also included are protective features consisting of input and
reference undervoltage lockouts each with hysteresis, cycle−by−cycle
current limiting, programmable output deadtime, and a latch for single
pulse metering.
These devices are available in an 8−pin dual−in−line and surface
mount (SOIC−8) plastic package as well as the 14−pin plastic surface
mount (SOIC−14). The SOIC−14 package has separate power and
ground pins for the totem pole output stage.
The UCX842B has UVLO thresholds of 16 V (on) and 10 V (off),
ideally suited for off−line converters. The UCX843B is tailored for
lower voltage applications having UVLO thresholds of 8.5 V (on) and
7.6 V (off).
Features
•Trimmed Oscillator for Precise Frequency Control
•Oscillator Frequency Guaranteed at 250 kHz
•Current Mode Operation to 500 kHz
•Automatic Feed Forward Compensation
•Latching PWM for Cycle−By−Cycle Current Limiting
•Internally Trimmed Reference with Undervoltage Lockout
•High Current Totem Pole Output
•Undervoltage Lockout with Hysteresis
•Low Startup and Operating Current
•Pb−Free Packages are Available
Figure 1. Simplified Block Diagram
5.0V
Reference
Latching
PWM
VCC
Undervoltage
Lockout
Oscillator
Error
Amplifier
7(12)
VC
7(11)
Output
6(10)
Power
Ground
5(8)
3(5)
Current
Sense
Input
Vref
8(14)
4(7)
2(3)
1(1) GND 5(9)
RT/CT
Voltage
Feedback
Input
R
R
+
−
Vref
Undervoltage
Lockout
Output
Compensation
Pin numbers in parenthesis are for the D suffix SOIC−14 package.
VCC
14
SOIC−14
D SUFFIX
CASE 751A
1
See detailed ordering and shipping information in the package
dimensions section on page 16 of this data sheet.
ORDERING INFORMATION
See general marking information in the device marking
section on page 18 of this data sheet.
DEVICE MARKING INFORMATION
1
8
PDIP−8
N SUFFIX
CASE 626
PIN CONNECTIONS
Compensation
NC
Voltage Feedback
NC
Current Sense
NC
RT/CT
Compensation
Voltage Feedback
Current Sense
RT/CT
Vref
Vref
NC
VCC
VC
Output
GND
Power Ground
VCC
Output
GND
(Top View)
8
7
6
5
1
2
3
4
1
2
3
4
14
13
12
11
5
6
7
10
9
8
(Top View)
SOIC−8
D1 SUFFIX
CASE 751
1
8
http://onsemi.com
UC3842B, UC3843B, UC2842B, UC2843B, NCV3843BV
http://onsemi.com
2
MAXIMUM RATINGS
Rating Symbol Value Unit
Bias and Driver Voltages (Zero Series Impedance, see also Total Device spec) VCC, VC30 V
Total Power Supply and Zener Current (ICC + IZ) 30 mA
Output Current, Source or Sink IO1.0 A
Output Energy (Capacitive Load per Cycle) W 5.0 mJ
Current Sense and Voltage Feedback Inputs Vin − 0.3 to + 5.5 V
Error Amp Output Sink Current IO10 mA
Power Dissipation and Thermal Characteristics
D Suffix, Plastic Package, SOIC−14 Case 751A
Maximum Power Dissipation @ TA = 25°C
Thermal Resistance, Junction−to−Air
D1 Suffix, Plastic Package, SOIC−8 Case 751
Maximum Power Dissipation @ TA = 25°C
Thermal Resistance, Junction−to−Air
N Suffix, Plastic Package, Case 626
Maximum Power Dissipation @ TA = 25°C
Thermal Resistance, Junction−to−Air
PD
RqJA
PD
RqJA
PD
RqJA
862
145
702
178
1.25
100
mW
°C/W
mW
°C/W
W
°C/W
Operating Junction Temperature TJ+150 °C
Operating Ambient Temperature UC3842B, UC3843B
UC2842B, UC2843B
UC3842BV, UC3843BV
NCV3843BV
TA0 to 70
− 25 to + 85
−40 to +105
−40 to +125
°C
Storage Temperature Range Tstg − 65 to +150 °C
Maximum ratings are those values beyond which device damage can occur. Maximum ratings applied to the device are individual stress limit
values (not normal operating conditions) and are not valid simultaneously. If these limits are exceeded, device functional operation is not implied,
damage may occur and reliability may be affected.
UC3842B, UC3843B, UC2842B, UC2843B, NCV3843BV
http://onsemi.com
3
ELECTRICAL CHARACTERISTICS (VCC = 15 V [Note 1], RT = 10 k, CT = 3.3 nF. For typical values TA = 25°C, for min/max values
TA is the operating ambient temperature range that applies [Note 2], unless otherwise noted.)
UC284XB UC384XB, XBV
Characteristics Symbol Min Typ Max Min Typ Max Unit
REFERENCE SECTION
Reference Output Voltage (IO = 1.0 mA, TJ = 25°C) Vref 4.95 5.0 5.05 4.9 5.0 5.1 V
Line Regulation (VCC = 12 V to 25 V) Regline − 2.0 20 − 2.0 20 mV
Load Regulation (IO = 1.0 mA to 20 mA) Regload − 3.0 25 − 3.0 25 mV
Temperature Stability TS− 0.2 − − 0.2 − mV/°C
Total Output Variation over Line, Load, and Temperature Vref 4.9 − 5.1 4.82 − 5.18 V
Output Noise Voltage (f = 10 Hz to 10 kHz, TJ = 25°C) Vn− 50 − − 50 − mV
Long Term Stability (TA = 125°C for 1000 Hours) S − 5.0 − − 5.0 − mV
Output Short Circuit Current ISC −30 −85 −180 −30 −85 −180 mA
OSCILLATOR SECTION
Frequency
TJ = 25°C
TA = Tlow to Thigh
TJ = 25°C (RT = 6.2 k, CT = 1.0 nF)
fOSC 49
48
225
52
−
250
55
56
275
49
48
225
52
−
250
55
56
275
kHz
Frequency Change with Voltage (VCC = 12 V to 25 V) DfOSC/DV− 0.2 1.0 − 0.2 1.0 %
Frequency Change with Temperature, TA = Tlow to Thigh DfOSC/DT− 1.0 − − 0.5 − %
Oscillator Voltage Swing (Peak−to−Peak) VOSC − 1.6 − − 1.6 − V
Discharge Current (VOSC = 2.0 V)
TJ = 25°C, TA = Tlow to Thigh UC284XB, UC384XB
TA = Tlow to Thigh UC384XBV
Idischg 7.8
7.5
−
8.3
−
−
8.8
8.8
−
7.8
7.6
7.2
8.3
−
−
8.8
8.8
8.8
mA
ERROR AMPLIFIER SECTION
Voltage Feedback Input (VO = 2.5 V) VFB 2.45 2.5 2.55 2.42 2.5 2.58 V
Input Bias Current (VFB = 5.0 V) IIB − − 0.1 −1.0 − − 0.1 − 2.0 mA
Open Loop Voltage Gain (VO = 2.0 V to 4.0 V) AVOL 65 90 − 65 90 − dB
Unity Gain Bandwidth (TJ = 25°C) BW 0.7 1.0 − 0.7 1.0 − MHz
Power Supply Rejection Ratio (VCC = 12 V to 25 V) PSRR 60 70 − 60 70 − dB
Output Current
Sink (VO = 1.1 V, VFB = 2.7 V)
Source (VO = 5.0 V, VFB = 2.3 V) ISink
ISource 2.0
− 0.5 12
−1.0 −
−2.0
− 0.5 12
−1.0 −
−
mA
Output Voltage Swing
High State (RL = 15 k to ground, VFB = 2.3 V)
Low State (RL = 15 k to Vref, VFB = 2.7 V)
UC284XB, UC384XB
UC384XBV
VOH
VOL 5.0
−
−
6.2
0.8
−
−
1.1
−
5.0
−
−
6.2
0.8
0.8
−
1.1
1.2
V
CURRENT SENSE SECTION
Current Sense Input Voltage Gain (Notes 3 and 4)
UC284XB, UC384XB
UC384XBV
AV2.85
−3.0
−3.15
−2.85
2.85 3.0
3.0 3.15
3.25
V/V
Maximum Current Sense Input Threshold (Note 3)
UC284XB, UC384XB
UC384XBV
Vth 0.9
−1.0
−1.1
−0.9
0.85 1.0
1.0 1.1
1.1
V
Power Supply Rejec tion Ratio (VCC = 12 V to 25 V, Not e 3) PSRR − 70 − − 70 − dB
Input Bias Current IIB − − 2.0 −10 − − 2.0 −10 mA
Propagation Delay (Current Sense Input to Output) tPLH(In/Out) − 150 300 − 150 300 ns
1. Adjust VCC above the Startup threshold before setting to 15 V.
2. Low duty cycle pulse techniques are used during test to maintain junction temperature as close to ambient as possible.
Tlow = 0°C for UC3842B, UC3843B; −25°C for UC2842B, UC2843B; −40°C for UC3842BV, UC3843BV
Thigh = +70°C for UC3842B, UC3843B; +85°C for UC2842B, UC2843B; +105°C for UC3842BV, UC3843BV
NCV3843BV: Tlow = −40°C, Thigh = +105°C. Guaranteed by design. NCV prefix is for automotive and other applications requiring site and
change control.
3. This parameter is measured at the latch trip point with VFB = 0 V.
4. Comparator gain is defined as: AVDV Output Compensation
DV Current Sense Input
UC3842B, UC3843B, UC2842B, UC2843B, NCV3843BV
http://onsemi.com
4
ELECTRICAL CHARACTERISTICS (VCC = 15 V [Note 5], RT = 10 k, CT = 3.3 nF. For typical values TA = 25°C, for min/max values
TA is the operating ambient temperature range that applies [Note 6], unless otherwise noted.)
UC284XB UC384XB, XBV
Characteristics Symbol Min Typ Max Min Typ Max Unit
OUTPUT SECTION
Output Voltage
Low State (ISink = 20 mA)
(ISink = 200 mA) UC284XB, UC384XB
UC384XBV
High State (ISource = 20 mA) UC284XB, UC384XB
UC384XBV
(ISource = 200 mA)
VOL
VOH
−
−
−
13
−
12
0.1
1.6
−
13.5
−
13.4
0.4
2.2
−
−
−
−
−
−
−
13
12.9
12
0.1
1.6
1.6
13.5
13.5
13.4
0.4
2.2
2.3
−
−
−
V
Output Voltage with UVLO Activated (VCC = 6.0 V, ISink = 1.0 mA) VOL(UVLO) − 0.1 1.1 − 0.1 1.1 V
Output Voltage Rise Time (CL = 1.0 nF, TJ = 25°C) tr− 50 150 − 50 150 ns
Output Voltage Fall Time (CL = 1.0 nF, TJ = 25°C) tf− 50 150 − 50 150 ns
UNDERVOLTAGE LOCKOUT SECTION
Startup Threshold (VCC)UCX842B, BV
UCX843B, BV
Vth 15
7.8 16
8.4 17
9.0 14.5
7.8 16
8.4 17.5
9.0
V
Minimum Operating Voltage After Turn−On (VCC)UCX842B, BV
UCX843B, BV
VCC(min) 9.0
7.0 10
7.6 11
8.2 8.5
7.0 10
7.6 11.5
8.2
V
PWM SECTION
Duty Cycle
Maximum UC284XB, UC384XB
Maximum UC384XBV
Minimum
DC(max)
DC(min)
94
−
−
96
−
−
−
−
0
94
93
−
96
96
−
−
−
0
%
TOTAL DEVICE
Power Supply Current
Startup (VCC = 6.5 V for UCX843B,
Startup VCC 14 V for UCX842B, BV)
(Note 5)
ICC + IC−
−
0.3
12
0.5
17
−
−
0.3
12
0.5
17
mA
Power Supply Zener Voltage (ICC = 25 mA) VZ30 36 − 30 36 − V
5. Adjust VCC above the Startup threshold before setting to 15 V.
6. Low duty cycle pulse techniques are used during test to maintain junction temperature as close to ambient as possible.
Tlow = 0°C for UC3842B, UC3843B; −25°C for UC2842B, UC2843B; −40°C for UC3842BV, UC3843BV
Thigh = +70°C for UC3842B, UC3843B; +85°C for UC2842B, UC2843B; +105°C for UC3842BV, UC3843BV
NCV3843BV: Tlow = −40°C, Thigh = +125°C. Guaranteed by design. NCV prefix is for automotive and other applications requiring site and
change control.
UC3842B, UC3843B, UC2842B, UC2843B, NCV3843BV
http://onsemi.com
5
0.8
2.0
5.0
8.0
20
50
80
RT, TIMING RESISTOR (k )
Ω
1.0 M500 k200 k100 k50 k20 k10 k
fOSC, OSCILLATOR FREQUENCY (kHz)
VCC = 15 V
TA = 25°C
Figure 2. Timing Resistor
versus Oscillator Frequency Figure 3. Output Deadtime
versus Oscillator Frequency
1.0 M500 k200 k100 k50 k20 k10 k
fOSC, OSCILLATOR FREQUENCY (kHz)
1.0
2.0
5.0
10
20
50
100
% DT, PERCENT OUTPUT DEADTIME
1
2
Figure 4. Oscillator Discharge Current
versus Temperature Figure 5. Maximum Output Duty Cycle
versus Timing Resistor
, DISCHARGE CURRENT (mA)
7.0
−55
TA, AMBIENT TEMPERATURE (°C)
−25 0 25 50 75 100 125
dischg
I
7.5
8.0
8.5
9.0
VCC = 15 V
VOSC = 2.0 V
, MAXIMUM OUTPUT DUTY CYCLE (%)
max
D
400.8
RT, TIMING RESISTOR (kW)
1.0 2.0 3.0 4.0 5.0 6.0 7.0 8.0
50
60
70
80
90
100
Idischg = 7.5 mA
VCC = 15 V
CT = 3.3 nF
TA = 25°C
1. CT = 10 nF
2. CT = 5.0 nF
3. CT = 2.0 nF
4. CT = 1.0 nF
5. CT = 500 pF
6. CT = 200 pF
7. CT = 100 pF
5
Idischg = 8.8 mA
7
3
6
4
VCC = 15 V
TA = 25°C
Figure 6. Error Amp Small Signal
Transient Response Figure 7. Error Amp Large Signal
Transient Response
1.0 ms/DIV0.5 ms/DIV
20 mV/DIV
20 mV/DIV
2.55 V
2.50 V
2.45 V
3.0 V
2.5 V
2.0 V
VCC = 15 V
AV = −1.0
TA = 25°C
VCC = 15 V
AV = −1.0
TA = 25°C
UC3842B, UC3843B, UC2842B, UC2843B, NCV3843BV
http://onsemi.com
6
Figure 8. Error Amp Open Loop Gain and
Phase versus Frequency Figure 9. Current Sense Input Threshold
versus Error Amp Output Voltage
Figure 10. Reference Voltage Change
versus Source Current Figure 11. Reference Short Circuit Current
versus Temperature
−20
AVOL , OPEN LOOP VOLTAGE GAIN (dB)
10 M10
f, FREQUENCY (Hz)
Gain
Phase
VCC = 15 V
VO = 2.0 V to 4.0 V
RL = 100 K
TA = 25°C
0
30
60
90
120
150
180
100 1.0 k 10 k 100 k 1.0 M
0
20
40
60
80
100
, EXCESS PHASE (DEGREES)
φ
0
VO, ERROR AMP OUTPUT VOLTAGE (V)
0
, CURRENT SENSE INPUT THRESHOLD (V
)
Vth
0.2
0.4
0.6
0.8
1.0
1.2
2.0 4.0 6.0 8.0
VCC = 15 V
TA = 25°C
TA = −55°C
TA = 125°C
ÄÄÄÄ
VCC = 15 V
ÄÄÄ
ÄÄÄ
TA = −55°C
ÄÄÄÄ
ÄÄÄÄ
TA = 25°C
, REFERENCE VOLTAGE CHANGE (mV)
−16
0
Iref, REFERENCE SOURCE CURRENT (mA)
20 40 60 80 100 120
ref
V
−12
−8.0
−4.0
0
Δ
−20
−24
ÄÄÄÄ
TA = 125°C
ÄÄÄÄ
ÄÄÄÄ
VCC = 15 V
RL ≤ 0.1 W
, REFERENCE SHORT CIRCUIT CURRENT (mA)
SC
I
50
−55
TA, AMBIENT TEMPERATURE (°C)
−25 0 25 50 75 100 125
70
90
110
Figure 12. Reference Load Regulation Figure 13. Reference Line Regulation
2.0 ms/DIV 2.0 ms/DIV
VCC = 15 V
IO = 1.0 mA to 20 mA
TA = 25°C
VCC = 12 V to 25
TA = 25°C
, OUTPUT VOLTAGE CHANGE (2.0 mV/DIV)
VO
Δ
, OUTPUT VOLTAGE CHANGE (2.0 mV/DIV)
VO
Δ
UC3842B, UC3843B, UC2842B, UC2843B, NCV3843BV
http://onsemi.com
7
ÄÄÄÄ
ÄÄÄÄ
Sink Saturation
(Load to VCC)
ÄÄÄÄ
ÄÄÄÄ
TA = −55°C
ÄÄÄ
VCC
Source Saturation
(Load to Ground)
0
Vsat, OUTPUT SATURATION VOLTAGE (V)
8000
IO, OUTPUT LOAD CURRENT (mA)
200 400 600
1.0
2.0
3.0
−2.0
−1.0
0
ÄÄÄ
ÄÄÄ
TA = −55°C
Figure 14. Output Saturation Voltage
versus Load Current Figure 15. Output Waveform
Figure 16. Output Cross Conduction Figure 17. Supply Current versus Supply Voltag
e
ÄÄÄ
ÄÄÄ
TA = 25°C
ÄÄÄÄ
ÄÄÄÄ
ÄÄÄÄ
ÄÄÄÄ
RT = 10 k
CT = 3.3 nF
VFB = 0 V
ISense = 0 V
TA = 25°C
, SUPPLY CURRENT (mA)
CC
I
00
VCC, SUPPLY VOLTAGE (V)
10 20 30 40
5
10
15
20
25
UCX843B
UCX842B
ÄÄÄÄ
ÄÄÄÄ
TA = 25°C
ÄÄ
GND
ÄÄÄÄÄ
ÄÄÄÄÄ
ÄÄÄÄÄ
VCC = 15 V
80 ms Pulsed Load
120 Hz Rate
VCC = 30 V
CL = 15 pF
TA = 25°C
VCC = 15 V
CL = 1.0 nF
TA = 25°C
50 ns/DIV
100 ns/DIV
100 mA/DIV 20 V/DIV
90%
10%
, OUTPUT VOLTAGE
O
V, SUPPLY CURRENT
CC
I
PIN FUNCTION DESCRIPTION
8−Pin 14−Pin Function Description
1 1 Compensation This pin is the Error Amplifier output and is made available for loop compensation.
2 3 Voltage
Feedback This is the inverting input of the Error Amplifier. It is normally connected to the switching power
supply output through a resistor divider.
3 5 Current
Sense A voltage proportional to inductor current is connected to this input. The PWM uses this
information to terminate the output switch conduction.
4 7 RT/CTThe Oscillator frequency and maximum Output duty cycle are programmed by connecting resistor
RT to Vref and capacitor CT to ground. Operation to 500 kHz is possible.
5 GND This pin is the combined control circuitry and power ground.
6 10 Output This output directly drives the gate of a power MOSFET. Peak currents up to 1.0 A are sourced
and sunk by this pin.
7 12 VCC This pin is the positive supply of the control IC.
8 14 Vref This is the reference output. It provides charging current for capacitor CT through resistor RT.
8 Power
Ground This pin is a separate power ground return that is connected back to the power source. It is used
to reduce the effects of switching transient noise on the control circuitry.
11 VCThe Output high state (VOH) is set by the voltage applied to this pin. With a separate power
source connection, it can reduce the effects of switching transient noise on the control circuitry.
9 GND This pin is the control circuitry ground return and is connected back to the power source ground.
2,4,6,1
3NC No connection. These pins are not internally connected.
UC3842B, UC3843B, UC2842B, UC2843B, NCV3843BV
http://onsemi.com
8
OPERATING DESCRIPTION
The UC3842B, UC3843B series are high performance,
fixed frequency, current mode controllers. They are
specifically designed for Off−Line and DC−to−DC
converter applications of fering the designer a cost−ef fective
solution with minimal external components. A
representative block diagram is shown in Figure 18.
Oscillator
The oscillator frequency is programmed by the values
selected for the timing components RT and CT. Capacitor CT
is charged from the 5.0 V reference through resistor RT to
approximately 2.8 V and discharged to 1.2 V by an internal
current sink. During the discharge of CT, the oscillator
generates an internal blanking pulse that holds the center
input of the NOR gate high. This causes the Output to be in
a low state, thus producing a controlled amount of output
deadtime. Figure 2 shows RT versus Oscillator Frequency
and Figure 3, Output Deadtime versus Frequency, both for
given values of CT. Note that many values of R T and CT will
give the same oscillator frequency but only one combination
will yield a specific output deadtime at a given frequency.
The oscillator thresholds are temperature compensated to
within ±6% at 50 kHz. Also because of industry trends
moving the UC384X into higher and higher frequency
applications, the UC384XB is guaranteed to within ±10% a t
250 kHz. These internal circuit refinements minimize
variations of oscillator frequency and maximum output duty
cycle. The results are shown in Figures 4 and 5.
In many noise−sensitive applications it may be desirable
to frequency−lock the converter to an external system clock.
This can be accomplished by applying a clock signal to the
circuit shown in Figure 21. For reliable locking, the
free−running oscillator frequency should be set about 10%
less than the clock frequency. A method for multi−unit
synchronization is shown in Figure 22. By tailoring the
clock waveform, accurate Output duty cycle clamping can
be achieved.
Error Amplifier
A fully compensated Error Amplifier with access to the
inverting input and output is provided. It features a typical
DC voltage gain of 90 dB, and a unity gain bandwidth of
1.0 MHz with 57 degrees of phase margin (Figure 8). The
non−inverting input is internally biased at 2.5 V and is not
pinned out. The converter output voltage is typically divided
down and monitored by the inverting input. The maximum
input bias current is −2.0 mA which can cause an output
voltage error that is equal to the product of the input bias
current and the equivalent input divider source resistance.
The Error Amp Output (Pin 1) is provided for external
loop compensation (Figure 32). The output voltage is offset
by two diode drops (≈1.4 V) and divided by three before it
connects to the non−inverting input of the Current Sense
Comparator. This guarantees that no drive pulses appear at
the Output (Pin 6) when pin 1 is at its lowest state (VOL).
This occurs when the power supply is operating and the load
is removed, or at the beginning of a soft−start interval
(Figures 24, 25). The Error Amp minimum feedback
resistance is limited by the amplifier’s source current
(0.5 mA) and the required output voltage (VOH) to reach the
comparator’s 1.0 V clamp level:
Rf(min) ≈3.0 (1.0 V) + 1.4 V
0.5 mA = 8800 W
Current Sense Comparator and PWM Latch
The UC3842B, UC3843B operate as a current mode
controller, whereby output switch conduction is initiated by
the oscillator and terminated when the peak inductor current
reaches the threshold level established by the Error
Amplifier Output/Compensation (Pin 1). Thus the error
signal controls the peak inductor current on a
cycle−by−cycle basis. The Current Sense Comparator PWM
Latch configuration used ensures that only a single pulse
appears at the Output during any given oscillator cycle. The
inductor current is converted to a voltage by inserting the
ground−referenced sense resistor RS in series with the
source of output switch Q1. This voltage is monitored by the
Current Se n s e Input (Pin 3) and compared to a level derived
from the Error Amp Output. The peak inductor current under
normal operating conditions is controlled by the voltage at
pin 1 where:
Ipk = V(Pin 1) − 1.4 V
3 RS
Abnormal operating conditions occur when the power
supply output is overloaded or if output voltage sensing is
lost. Under these conditions, the Current Sense Comparator
threshold will be internally clamped to 1.0 V. Therefore the
maximum peak switch current is:
Ipk(max) = 1.0 V
RS
When designing a high power switching regulator it
becomes desirable to reduce the internal clamp voltage in
order to keep the power dissipation of RS to a reasonable
level. A simple method to adjust this voltage is shown in
Figure 23. The two external diodes are used to compensate
the internal diodes, yielding a constant clamp voltage over
temperature. Erratic operation due to noise pickup can result
if there is an excessive reduction of the Ipk(max) clamp
voltage.
A narrow spike on the leading edge of the current
waveform can usually be observed and may cause the power
supply to exhibit an instability when the output is lightly
loaded. This spike is due to the power transformer
interwinding capacitance and output rectifier recovery time.
The addition of an RC filter on the Current Sense Input with
a time constant that approximates the spike duration will
usually eliminate the instability (refer to Figure 27).
UC3842B, UC3843B, UC2842B, UC2843B, NCV3843BV
http://onsemi.com
9
+
−
Reference
Regulator
VCC
UVLO
+
−Vref
UVLO
3.6V
36V
S
R
Q
Internal
Bias
+1.0mA
Oscillator
2.5V
R
R
R
2R
Error
Amplifier
Voltage
Feedback
Input
Output/
Compensation Current Sense
Comparator
1.0V
VCC 7(12)
GND 5(9)
VC
7(11)
Output
6(10)
Power Ground
5(8)
Current Sense Input
3(5) RS
Q1
VCC Vin
1(1)
2(3)
4(7)
8(14)
RT
CT
Vref
= Sink Only Positive True Logic
Pin numbers adjacent to terminals are for the 8−pin dual−in−line package.
Pin numbers in parenthesis are for the D suffix SOIC−14 package.
Figure 18. Representative Block Diagram
Figure 19. Timing Diagram
Large RT/Small CTSmall RT/Large CT
PWM
Latch
(See
Text)
Capacitor CT
Latch
Set" Input
Output/
Compensation
Current Sense
Input
Latch
Reset" Input
Output
UC3842B, UC3843B, UC2842B, UC2843B, NCV3843BV
http://onsemi.com
10
Undervoltage Lockout
Two undervoltage lockout comparators have been
incorporated to guarantee that the IC is fully functional
before the output stage is enabled. The positive power
supply terminal (VCC) and the reference output (Vref) are
each monitored by separate comparators. Each has built−in
hysteresis to prevent erratic output behavior as their
respective thresholds are crossed. The VCC comparator
upper and lower thresholds are 16 V/10 V for the UCX842B,
and 8.4 V/7.6 V for the UCX843B. The Vref comparator
upper and lower thresholds are 3.6 V/3.4 V. The large
hysteresis and low startup current of the UCX842B makes
it ideally suited in off−line converter applications where
efficient bootstrap startup techniques are required
(Figure 34). The UCX843B is intended for lower voltage
DC−to−DC converter applications. A 36 V Zener is
connected as a shunt regulator from VCC to ground. Its
purpose is to protect the IC from excessive voltage that can
occur during system startup. The minimum operating
voltage (VCC) for the UCX842B is 11 V and 8.2 V for the
UCX843B.
These devices contain a single totem pole output stage that
was specifically designed for direct drive of power
MOSFETs. It is capable of up to ±1.0 A peak drive current
and has a typical rise and fall time of 50 ns with a 1.0 nF load.
Additional internal circuitry has been added to keep the
Output in a sinking mode whenever an undervoltage lockout
is active. This characteristic eliminates the need for an
external pull−down resistor.
The SOIC−14 surface mount package provides separate
pins for VC (output supply) and Power Ground. Proper
implementation will significantly reduce the level of
switching transient noise imposed on the control circuitry.
This becomes particularly useful when reducing the Ipk(max)
clamp level. The separate VC supply input allows the
designer added flexibility in tailoring the drive voltage
independent of VCC. A Zener clamp is typically connected
to this input when driving power MOSFETs in systems
where VCC is greater than 20 V. Figure 26 shows proper
power and control ground connections in a current−sensing
power MOSFET application.
Reference
The 5.0 V bandgap reference is trimmed to ±1.0%
tolerance at T J = 25°C on the UC284XB, and ±2.0% on the
UC384XB. Its primary purpose is to supply char ging current
to the oscillator timing capacitor. The reference has short−
circuit protection and is capable of providing in excess of
20 mA for powering additional control system circuitry.
Design Considerations
Do not attempt to construct the converter on
wire−wrap or plug−in pr ototype boards. High frequency
circuit layout techniques are imperative to prevent
pulse−width jitter. This is usually caused by excessive noise
pick−up imposed on the Current Sense or Voltage Feedback
inputs. Noise immunity can be improved by lowering circuit
impedances at these points. The printed circuit layout should
contain a ground plane with low−current signal and
high−current switch and output grounds returning on
separate paths back to the input filter capacitor. Ceramic
bypass capacitors (0.1 mF) connected directly to VCC, VC,
and Vref may be required depending upon circuit layout.
This provides a low impedance path for filtering the high
frequency noise. All high current loops should be kept as
short as possible using heavy copper runs to minimize
radiated EMI. The Error Amp compensation circuitry and
the converter output voltage divider should be located close
to the IC and as far as possible from the power switch and
other noise−generating components.
Current mode converters can exhibit subharmonic
oscillations when operating at a duty cycle greater than 5 0%
with continuous inductor current. This instability is
independent of the regulator’s closed loop characteristics
and is caused by the simultaneous operating conditions of
fixed frequency and peak current detecting. Figure 20A
shows the phenomenon graphically. At t0, switch
conduction begins, causing the inductor current to rise at a
slope of m1. This slope is a function of the input voltage
divided by the inductance. At t1, the Current Sense Input
reaches the threshold established by the control voltage.
This causes the switch to turn off and the current to decay at
a slope of m2, until the next oscillator cycle. The unstable
condition can be shown if a perturbation is added to the
control voltage, resulting in a small DI (dashed line). With
a fixed oscillator period, the current decay time is reduced,
and the minimum current at switch turn−on (t2) is increased
by DI + DI m2/m1. The minimum current at the next cycle
(t3) decreases to (DI + DI m2/m1) (m2/m1). This perturbation
is multiplied by m2/m1 on each succeeding cycle, alternately
increasing and decreasing the inductor current at switch
turn−on. Several oscillator cycles may be required before
the inductor current reaches zero causing the process to
commence again. If m2/m1 is greater than 1, the converter
will be unstable. Figure 20B shows that by adding an
artificial ramp that is synchronized with the PWM clock to
the control voltage, the DI perturbation will decrease to zero
on succeeding cycles. This compensating ramp (m3) must
have a slope equal to or slightly greater than m2/2 for
stability. With m2/2 slope compensation, the average
inductor current follows the control voltage, yielding true
current mode operation. The compensating ramp can be
derived from the oscillator and added to either the Voltage
Feedback or Current Sense inputs (Figure 33).
UC3842B, UC3843B, UC2842B, UC2843B, NCV3843BV
http://onsemi.com
11
Figure 20. Continuous Current Waveforms
2(3) EA
Bias
+
Osc
R
R
R
2R
5(9)
1(1)
4(7)
8(14)
RT
CT
Vref
0.01
The diode clamp is required if the Sync amplitude is large enough to cause the bottom
side of CT to go more than 300 mV below ground.
External
Sync
Input
47
+
R
R
R
2R
Bias
Osc
EA
5(9)
1(1)
2(3)
4(7)
8(14)
To Additional
UCX84XBs
R
S
Q
8 4
6
5
2
1
C
3
7
RA
RB5.0k
5.0k
5.0k MC1455
f +1.44
(RA)2R
B)C D(max) +RB
RA)2R
B
+
−
5.0V Ref
+
−
S
R
Q
Bias
+
Osc
R
R
R
2R
EA
1.0V
5(9)
7(11)
6(10)
5(8)
3(5) RS
Q1
VCC Vin
1(1)
2(3)
4(7)
8(14)
R1
VClamp
R2
7(12)
Comp/Latch
1.0 mA
Ipk(max)[VClamp
RS
Where: 0 ≤ VClamp ≤ 1.0 V
VClamp ≈
1.67
ǒR2
R1)1Ǔ+ 0.33x10−3 ǒR1R2
R1)R2Ǔ
Control Voltage
Inductor
Current
Oscillator Period
Control Voltage
Inductor
Current
Oscillator Period
(A)
(B)
m1m2
t0t1t2t3
m3
m2
t4t5t6
DI
m1
DI
Dl)Dlm2
m1Dl)Dlm2
m1 m2
m1
Figure 21. External Clock Synchronization
Figure 22. External Duty Cycle Clamp and
Multi−Unit Synchronization Figure 23. Adjustable Reduction of Clamp Level
UC3842B, UC3843B, UC2842B, UC2843B, NCV3843BV
http://onsemi.com
12
+
−
+
−
S
R
+
R
R
R
2R
VClamp [1.67
ǒR2
R1)1Ǔ
Ipk(max)[VClamp
RS
5.0V Ref
Q
Bias
Osc
EA
1.0V
5(9)
7(11)
6(10)
5(8)
3(5) RS
Q1
VCC Vin
1(1)
2(3)
4(7)
8(14)
R1
VClamp
R2
Where: 0 ≤ VClamp ≤ 1.0 V
CMPSA63
tSoft-Start +*Inƪ1*VC
3VClampƫC R1R2
R1)R
2
7(12)
1.0 mA
Comp/Latch
5.0V Ref
+
−
S
R
Q
Bias
+
1.0mA
Osc
R
R
R
2R
EA 1.0V
5(9)
1(1)
2(3)
4(7)
8(14)
C
1.0M
tSoft−Start ≈ 3600C in mF
Figure 24. Soft−Start Circuit Figure 25. Adjustable Buffered Reduction of
Clamp Level with Soft−Start
+
−
5.0V Ref
+
−
S
R
Q
(11)
(10)
(8)
Comp/Latch
(5) RS
1/4 W
VCC Vin
K
M
DSENSEFET
G
S
Power Ground:
To Input Source
Return
Control Circuitry Ground:
To Pin (9)
Virtually lossless current sensing can be achieved with the implementation of a
SENSEFET power switch. For proper operation during over−current conditions, a
reduction of the Ipk(max) clamp level must be implemented. Refer to Figures 23 and 25.
VPin 5 [RSIpk rDS(on)
rDM(on) )RS
If: SENSEFET = MTP10N10M
RS = 200
Then : VPin5[ 0.075Ipk
(12)
Figure 26. Current Sensing Power MOSFET
+
−
5.0V Ref
+
−
S
R
Q
7(11)
6(10)
5(8)
3(5)
RS
Q1
VCC Vin
C
R
The addition of the RC filter will eliminate instability caused by the leading
edge spike on the current waveform.
7(12)
Comp/Latch
Figure 27. Current Waveform Spike Suppression
UC3842B, UC3843B, UC2842B, UC2843B, NCV3843BV
http://onsemi.com
13
Figure 28. MOSFET Parasitic Oscillations
6(10)
5(8)
3(5) RS
Q1
Vin
C1
Base Charge
Removal
The totem pole output can furnish negative base current for enhanced
transistor turn−off, with the addition of capacitor C1.
S
R
5.0V Ref
Q
7(11)
6(10)
5(8)
3(5)
RS
Q1
VCC
IB
+
−
0
Vin
Isolation
Boundary
VGS Waveforms
+
−
0
+
−
0
50% DC 25% DC
Ipk+V(Pin1) *1.4
3RSǒNS
NpǓ
Comp/Latch
7(12)
R
CNSNP
+
−
+
−
Bias
+
Osc
R
R
R
2R
EA
5(9)
1(1)
2(3)
4(7)
8(14)
The MCR101 SCR must be selected for a holding of < 0.5 mA @ TA(min). The simple two
transistor circuit can be used in place of the SCR as shown. All resistors are 10 k.
MCR
101
2N
3905
2N
3903
1.0 mA
S
R
5.0V Ref
Q
7(11)
6(10)
5(8)
3(5) RS
Q1
VCC Vin
Series gate resistor Rg will damp any high frequency parasitic oscillations
caused by the MOSFET input capacitance and any series wiring inductance in
the gate−source circuit.
7(12)
Rg
Comp/Latch
+
−
+
−
Figure 29. Bipolar Transistor Drive
Figure 30. Isolated MOSFET Drive Figure 31. Latched Shutdown
UC3842B, UC3843B, UC2842B, UC2843B, NCV3843BV
http://onsemi.com
14
+
−
+
−
5.0V Ref
36V
S
RQ
Bias
+
1.0mA
Osc
R
R
R
2R
EA 1.0V
7(12)
7(11)
6(10)
5(8)
3(5) RS
VCC Vin
1(1)
2(3)
4(7)
8(14)
RT
CT
The buffered oscillator ramp can be resistively summed with either the voltage
feedback or current sense inputs to provide slope compensation.
m
− 3.0m
−m
Rf
Cf
Ri
Rd
From VORSlope
MPS3904
5(9)
Comp/Latch
Figure 32. Error Amplifier Compensation
+
R
2R
1.0mA
EA
2(3)
5(9)
2.5V
1(1)
Rf
Cf
Rd
Ri
From VO
Error Amp compensation circuit for stabilizing any current mode topology except for boost and flyback
converters operating with continuous inductor current.
Rf ≥ 8.8 k
+
R
2R
1.0mA
EA
2(3)
5(9)
2.5V
1(1)
Rf
Cf
Rd
Rp
From VO
Error Amp compensation circuit for stabilizing current mode boost and flyback
topologies operating with continuous inductor current.
Cp
Ri
Figure 33. Slope Compensation
UC3842B, UC3843B, UC2842B, UC2843B, NCV3843BV
http://onsemi.com
15
Figure 34. 27 W Off−Line Flyback Regulator
MUR110
+
−
+
−
S
R
+
R
R
5.0V Ref
Q
Bias
EA
5(9)
7(11)
6(10)
5(8)
3(5) 0.5
MTP
4N50
1(1)
2(3)
4(7)
8(14)
10k
4700pF
470pF
150k
100
pF
18k
4.7k
0.01
100
+
1.0k
115 Vac
4.7WMDA
202
250
56k
4.7k 3300
pF
1N4935 1N4935
++
68
47
1N4937
1N4937
680pF
2.7k
L3
L2
L1
++
++
++
1000
1000
2200
10
10
1000
5.0V/4.0A
5.0V RTN
12V/0.3A
±12V RTN
−12V/0.3A
Primary: 45 Turns #26 AWG
Secondary ±12 V: 9 Turns #30 AWG
(2 Strands) Bifiliar Wound
Secondary 5.0 V: 4 Turns (six strands)
#26 Hexfiliar Wound
Secondary Feedback: 10 Turns
#30 AWG (2 strands) Bifiliar Wound
Core: Ferroxcube EC35−3C8
Bobbin: Ferroxcube EC35PCB1
Gap: ≈ 0.10" for a primary inductance
of 1.0 mH
MUR110
MBR1635
T1
22
Osc
T1 −
7(12)
Comp/Latch
L1
L2, L3
− 15 mH at 5.0 A, Coilcraft Z7156
− 25 mH at 5.0 A, Coilcraft Z7157
1N5819
Test Conditions Results
Line Regulation: 5.0 V
±12V Vin = 95 to 130 Vac D = 50 mV or ±0.5%
D = 24 mV or ±0.1%
Load Regulation: 5.0 V
±12V
Vin = 115 Vac,
Iout = 1.0 A to 4.0 A
Vin = 115 Vac,
Iout = 100 mA to 300 mA
D = 300 mV or ±3.0%
D = 60 mV or ±0.25%
Output Ripple: 5.0 V
±12V Vin = 115 Vac 40 mVpp
80 mVpp
Efficiency Vin = 115 Vac 70%
All outputs are at nominal load currents, unless otherwise noted
UC3842B, UC3843B, UC2842B, UC2843B, NCV3843BV
http://onsemi.com
16
ORDERING INFORMATION
Device Operating Temperature Range Package Shipping†
UC2842BD
TA = −25° to +85°C
SOIC−14 55 Units/Rail
UC2842BDG SOIC−14
(Pb−Free) 55 Units/Rail
UC2842BD1 SOIC−8 98 Units/Rail
UC2842BD1G SOIC−8
(Pb−Free) 98 Units/Rail
UC2842BD1R2 SOIC−8 2500 Tape & Reel
UC2842BD1R2G SOIC−8
(Pb−Free) 2500 Tape & Reel
UC2842BN PDIP−8
1000 Units/Rail
UC2842BNG PDIP−8
(Pb−Free)
UC3842BN
TA = 0° to +70°C
PDIP−8
UC3842BNG PDIP−8
(Pb−Free)
UC3842BD SOIC−14 55 Units/Rail
UC3842BDG SOIC−14
(Pb−Free) 55 Units/Rail
UC3842BDR2 SOIC−14 2500 Tape & Reel
UC3842BDR2G SOIC−14
(Pb−Free) 2500 Tape & Reel
UC3842BD1 SOIC−8 98 Units/Rail
UC3842BD1G SOIC−8
(Pb−Free) 98 Units/Rail
UC3842BD1R2 SOIC−8
2500 Tape & Reel
UC3842BD1R2G SOIC−8
(Pb−Free)
UC3842BVDR2
TA = −40° to +105°C
SOIC−14
UC3842BVDR2G SOIC−14
(Pb−Free)
UC3842BVD1 SOIC−8 98 Units/Rail
UC3842BVD1G SOIC−8
(Pb−Free) 98 Units/Rail
UC3842BVD1R2 SOIC−8 2500 Tape & Reel
UC3842BVD1R2G SOIC−8
(Pb−Free) 2500 Tape & Reel
UC2843BD
TA = −25° to +85°C
SOIC−14 55 Units/Rail
UC2843BDG SOIC−14
(Pb−Free) 55 Units/Rail
UC2843BDR2 SOIC−14 2500 Tape & Reel
UC2843BDR2G SOIC−14
(Pb−Free) 2500 Tape & Reel
UC2843BD1 SOIC−8 98 Units/Rail
UC2843BD1G SOIC−8
(Pb−Free) 98 Units/Rail
UC2843BD1R2
TA = −25° to +85°C
SOIC−8 2500 Tape & Reel
UC2843BD1R2G SOIC−8
(Pb−Free) 2500 Tape & Reel
UC2843BN PDIP−8 1000 Units/Rail
UC2843BNG PDIP−8
(Pb−Free) 1000 Units/Rail
†For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging
Specifications Brochure, BRD8011/D.
UC3842B, UC3843B, UC2842B, UC2843B, NCV3843BV
http://onsemi.com
17
ORDERING INFORMATION
Device Operating Temperature Range Package Shipping†
UC3843BD
TA = 0° to +70°C
SOIC−14 55 Units/Rail
UC3843BDG SOIC−14
(Pb−Free) 55 Units/Rail
UC3843BDR2 SOIC−14 2500 Tape & Reel
UC3843BDR2G SOIC−14
(Pb−Free) 2500 Tape & Reel
UC3843BD1 SOIC−8 98 Units/Rail
UC3843BD1G SOIC−8
(Pb−Free) 98 Units/Rail
UC3843BD1R2 SOIC−8
2500 Tape & Reel
UC3843BD1R2G SOIC−8
(Pb−Free)
UC3843BDR2 SOIC−14
UC3843BDR2G SOIC−14
(Pb−Free)
UC3843BN PDIP−8 1000 Units/Rail
UC3843BNG PDIP−8
(Pb−Free) 1000 Units/Rail
UC3843BVD
TA = −40° to +105°C
SOIC−14 55 Units/Rail
UC3843BVDG SOIC−14
(Pb−Free) 55 Units/Rail
UC3843BVDR2 SOIC−14 2500 Tape & Reel
UC3843BVDR2G SOIC−14
(Pb−Free) 2500 Tape & Reel
UC3843BVD1 SOIC−8 98 Units/Rail
UC3843BVD1G SOIC−8
(Pb−Free) 98 Units/Rail
UC3843BVD1R2 SOIC−8 2500 Tape & Reel
UC3843BVD1R2G SOIC−8
(Pb−Free) 2500 Tape & Reel
UC3843BVN PDIP−8 1000 Units/Rail
UC3843BVNG PDIP−8
(Pb−Free) 1000 Units/Rail
NCV3843BVDR2 TA = −40° to +125°CSOIC−14 2500 Tape & Reel
NCV3843BVDR2G SOIC−14
(Pb−Free) 2500 Tape & Reel
†For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging
Specifications Brochure, BRD8011/D.
UC3842B, UC3843B, UC2842B, UC2843B, NCV3843BV
http://onsemi.com
18
SOIC−14
D SUFFIX
CASE 751A
SOIC−8
D1 SUFFIX
CASE 751
MARKING DIAGRAMS
PDIP−8
N SUFFIX
CASE 626
*This marking diagram also applies to NCV3843BV.
*
x = 2 or 3
A = Assembly Location
WL, L = Wafer Lot
YY, Y = Year
WW, W = Work Week
G or G= Pb−Free Package
UC3843BVN
AWL
YYWWG
1
8
UC384xBVDG
AWLYWW
1
14
384xB
ALYWV
G
1
8
UC384xBN
AWL
YYWWG
1
8
UC284xBN
AWL
YYWWG
1
8
UC384xBDG
AWLYWW
1
14
UC284xBDG
AWLYWW
1
14
384xB
ALYW
G
1
8284xB
ALYW
G
1
8
UC3842B, UC3843B, UC2842B, UC2843B, NCV3843BV
http://onsemi.com
19
PACKAGE DIMENSIONS
PDIP−8
N SUFFIX
CASE 626−05
ISSUE L
NOTES:
1. DIMENSION L TO CENTER OF LEAD WHEN
FORMED PARALLEL.
2. PACKAGE CONTOUR OPTIONAL (ROUND OR
SQUARE CORNERS).
3. DIMENSIONING AND TOLERANCING PER ANSI
Y14.5M, 1982.
14
58
F
NOTE 2 −A−
−B−
−T−
SEATING
PLANE
H
J
GDK
N
C
L
M
M
A
M
0.13 (0.005) B M
T
DIM MIN MAX MIN MAX
INCHESMILLIMETERS
A9.40 10.16 0.370 0.400
B6.10 6.60 0.240 0.260
C3.94 4.45 0.155 0.175
D0.38 0.51 0.015 0.020
F1.02 1.78 0.040 0.070
G2.54 BSC 0.100 BSC
H0.76 1.27 0.030 0.050
J0.20 0.30 0.008 0.012
K2.92 3.43 0.115 0.135
L7.62 BSC 0.300 BSC
M−−− 10 −−− 10
N0.76 1.01 0.030 0.040
__
SOIC−14
D SUFFIX
CASE 751A−03
ISSUE G
NOTES:
1. DIMENSIONING AND TOLERANCING PER
ANSI Y14.5M, 1982.
2. CONTROLLING DIMENSION: MILLIMETER.
3. DIMENSIONS A AND B DO NOT INCLUDE
MOLD PROTRUSION.
4. MAXIMUM MOLD PROTRUSION 0.15 (0.006)
PER SIDE.
5. DIMENSION D DOES NOT INCLUDE
DAMBAR PROTRUSION. ALLOWABLE
DAMBAR PROTRUSION SHALL BE 0.127
(0.005) TOTAL IN EXCESS OF THE D
DIMENSION AT MAXIMUM MATERIAL
CONDITION.
−A−
−B−
G
P7 PL
14 8
7
1
M
0.25 (0.010) B M
S
B
M
0.25 (0.010) A S
T
−T−
F
RX 45
SEATING
PLANE D14 PL K
C
J
M
_
DIM MIN MAX MIN MAX
INCHESMILLIMETERS
A8.55 8.75 0.337 0.344
B3.80 4.00 0.150 0.157
C1.35 1.75 0.054 0.068
D0.35 0.49 0.014 0.019
F0.40 1.25 0.016 0.049
G1.27 BSC 0.050 BSC
J0.19 0.25 0.008 0.009
K0.10 0.25 0.004 0.009
M0 7 0 7
P5.80 6.20 0.228 0.244
R0.25 0.50 0.010 0.019
__ __
UC3842B, UC3843B, UC2842B, UC2843B, NCV3843BV
http://onsemi.com
20
PACKAGE DIMENSIONS
SOIC−8
D1 SUFFIX
CASE 751−07
ISSUE AG
1.52
0.060
7.0
0.275
0.6
0.024 1.270
0.050
4.0
0.155
ǒmm
inchesǓ
SCALE 6:1
*For additional information on our Pb−Free strategy and soldering
details, please download the ON Semiconductor Soldering and
Mounting Techniques Reference Manual, SOLDERRM/D.
SOLDERING FOOTPRINT*
SEATING
PLANE
1
4
58
N
J
X 45_
K
NOTES:
1. DIMENSIONING AND TOLERANCING PER
ANSI Y14.5M, 1982.
2. CONTROLLING DIMENSION: MILLIMETER.
3. DIMENSION A AND B DO NOT INCLUDE
MOLD PROTRUSION.
4. MAXIMUM MOLD PROTRUSION 0.15 (0.006)
PER SIDE.
5. DIMENSION D DOES NOT INCLUDE DAMBAR
PROTRUSION. ALLOWABLE DAMBAR
PROTRUSION SHALL BE 0.127 (0.005) TOTAL
IN EXCESS OF THE D DIMENSION AT
MAXIMUM MATERIAL CONDITION.
6. 751−01 THRU 751−06 ARE OBSOLETE. NEW
STANDARD IS 751−07.
A
BS
D
H
C
0.10 (0.004)
DIM
AMIN MAX MIN MAX
INCHES
4.80 5.00 0.189 0.197
MILLIMETERS
B3.80 4.00 0.150 0.157
C1.35 1.75 0.053 0.069
D0.33 0.51 0.013 0.020
G1.27 BSC 0.050 BSC
H0.10 0.25 0.004 0.010
J0.19 0.25 0.007 0.010
K0.40 1.27 0.016 0.050
M0 8 0 8
N0.25 0.50 0.010 0.020
S5.80 6.20 0.228 0.244
−X−
−Y−
G
M
Y
M
0.25 (0.010)
−Z−
Y
M
0.25 (0.010) ZSXS
M
____
ON Semiconductor and are registered trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC reserves the right to make changes without further notice
to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does SCILLC assume any liability
arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages.
“Typical” parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All
operating parameters, including “Typicals” must be validated for each customer application by customer’s technical experts. SCILLC does not convey any license under its patent rights
nor the rights of others. SCILLC products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications
intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where personal injury or death may occur. Should
Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and its of ficers, employees, subsidiaries, affiliates,
and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death
associated with such unintended or unauthorized use, even if such claim alleges that SCILLC was negligent regarding the design or manufacture of the part. SCILLC is an Equal
Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner.
PUBLICATION ORDERING INFORMATION
N. American Technical Support: 800−282−9855 Toll Free
USA/Canada
Japan: ON Semiconductor, Japan Customer Focus Center
2−9−1 Kamimeguro, Meguro−ku, Tokyo, Japan 153−0051
Phone: 81−3−5773−3850
UC3842A/D
SENSEFET is a trademark of Semiconductor Components Industries, LLC.
LITERATURE FULFILLMENT:
Literature Distribution Center for ON Semiconductor
P.O. Box 61312, Phoenix, Arizona 85082−1312 USA
Phone: 480−829−7710 or 800−344−3860 Toll Free USA/Canada
Fax: 480−829−7709 or 800−344−3867 Toll Free USA/Canada
Email: orderlit@onsemi.com
ON Semiconductor Website: http://onsemi.com
Order Literature: http://www.onsemi.com/litorder
For additional information, please contact your
local Sales Representative.