TECHNICAL DATA SHEET
6 Lake Street, Lawrence, MA 01841 Gort Road Business Park, Ennis, Co. Clare, Ireland
1-800-446-1158 / (978) 620-2600 / Fax: ( 978) 689-0803 Tel: +353 (0) 65 6840044 Fax: +353 (0) 65 6822298
Website: http://www.microsemi.com N-CHANNEL MOSFET
Qualified per MIL-PRF-19500/556
T4-LDS-0064 Rev. 2 (110115) Page 1 of 4
DEVICES LEVELS
2N6782 2N6782U JAN
JANTX
JANTXV
ABSOLUTE MAXIMUM RATI NG S (TC = +25°C unless otherwise noted)
Parameters / Test Conditions Symbol Value Unit
Drain – Source Voltage VDS 100 Vdc
Gate – Source Voltage VGS ± 20 Vdc
Continuous Drain Current
T
C = +25°C ID1 3.5 Adc
Continuous Drain Current
T
C = +100°C ID2 2.25 Adc
Max. Power Dissipation Ptl 15
(1) W
Drain to Source On State Resistance Rds(on) 0.61(2) Ω
Operating & Storage Temperature Top, Tstg -55 to +150 °C
Note: (1) Derated Linearly by 0.12 W/°C for TC > +25°C
(2) VGS = 10Vdc, ID = 3.5A
ELECTRICAL CHARACTERISTICS (TA = +25°C, unless otherwise noted)
Parameters / Test Conditions Symbol Min. Max. Unit
OFF CHARACTERTICS
Drain-Source Breakdown Voltage
VGS = 0V, ID = 1mAdc V(BR)DSS 100 Vdc
Gate-Source Voltage (Threshold)
VDS ≥ VGS, ID = 0.25mA
VDS ≥ VGS, ID = 0.25mA, Tj = +125°C
VDS ≥ VGS, ID = 0.25mA, Tj = -55°C
VGS(th)1
VGS(th)2
VGS(th)3
2.0
1.0
4.0
5.0
Vdc
Gate Current
VGS = ±20V, VDS = 0V
VGS = ±20V, VDS = 0V, Tj = +125°C
IGSS1
IGSS2
±100
±200 nAdc
Drain Current
VGS = 0V, VDS = 80V
VGS = 0V, VDS = 80V, Tj = +125°C
IDSS1
IDSS2
25
0.25
µAdc
mAdc
Static Drain-Source On-State Resistance
VGS = 10V, ID = 2.25A pulsed
VGS = 10V, ID = 3.5A pulsed
Tj = +125°C
VGS = 10V, ID = 2.25A pulsed
rDS(on)1
rDS(on)2
rDS(on)3
0.60
0.61
1.08
Ω
Ω
Ω
Diode Forward Voltage
VGS = 0V, ID = 3.5A pulsed VSD 1.5 Vdc
TO-205AF
(formerly TO-39)
U – 18 LCC
TECHNICAL DATA SHEET
6 Lake Street, Lawrence, MA 01841 Gort Road Business Park, Ennis, Co. Clare, Ireland
1-800-446-1158 / (978) 620-2600 / Fax: ( 978) 689-0803 Tel: +353 (0) 65 6840044 Fax: +353 (0) 65 6822298
Website: http://www.microsemi.com
T4-LDS-0064 Rev. 2 (110115) Page 2 of 4
DYNAMIC CHARACTERISTICS
Parameters / Test Conditions Symbol Min. Max. Unit
Gate Charge: Qg(on)
Qgs
Qgd
nC
On-State Gate Charge
Gate to Source Charge
Gate to Drain Charge
VGS = 10V, ID = 3.5A
VDS = 50V
8.1
1.7
4.5
SWITCHING CHARACTERISTICS
Parameters / Test Conditions Symbol Min. Max. Unit
Switching time tests:
Turn-on delay time
Rinse time
Turn-off delay time
Fall time
ID = 3.5A, VGS = 10Vdc,
Gate drive impedance = 7.5Ω,
VDD = 50Vdc
td(on)
tr
td(off)
tf
15
25
25
20
ns
Diode Reverse Recovery Time di/dt ≤ 100A/µs, VDD ≤ 50V, ID = 3.5A
IF = 3.5A trr 180 ns
TECHNICAL DATA SHEET
6 Lake Street, Lawrence, MA 01841 Gort Road Business Park, Ennis, Co. Clare, Ireland
1-800-446-1158 / (978) 620-2600 / Fax: ( 978) 689-0803 Tel: +353 (0) 65 6840044 Fax: +353 (0) 65 6822298
Website: http://www.microsemi.com
T4-LDS-0064 Rev. 2 (110115) Page 3 of 4
PACKAGE DIMENSIONS
NOTES:
1. Dimensions are in inches. Millimeters are given for general information only.
2. Beyond radius (r) maximum, J shall be held for a minimum length of .011 (0.28 mm).
3. Dimension k measured from maximum HD.
4. Outline in this zone is not controlled.
5. Dimension CD shall not vary more than .010 (0.25 mm) in zone P. This zone is controlled for automatic handling.
6. Leads at gauge plane .054 +.001, -.000 (1.37 +0.03, -0.00 mm) below seating plane shall be within .007 (0.18 mm) radius
of true position (TP) at maximum material condition (MMC) relative to tab at MMC.
7. LU applies between L1 and L2. LD applies between L2 and L minimum. Diameter is uncontrolled in L1 and beyond LL
minimum.
8. All three leads.
9. Radius (r) applies to both inside corners of tab.
10. Drain is electrically connected to the case.
11. In accordance with ASME Y14.5M, diameters are equivalent to φx symbology.
FIGURE 1. Physical dimensions for TO-205AF.
Dimensions
Ltr Inches Millimeters Notes
Min Max Min Max
CD .305 .335 7.75 8.51
CH .160 .180 4.06 4.57
HD .335 .370 8.51 9.40
h .009 .041 0.23 1.04
J .028 .034 0.71 0.86 2
k .029 .045 0.74 1.14 3
LD .016 .021 0.41 0.53 7, 8
LL .500 .750 12.7 19.05 7, 8
LS .200 TP 5.08 TP 6
LU .016 .019 0.41 0.48 7, 8
L1 .050 1.27 7, 8
L2 .250 6.35 7, 8
P .100 2.54 5
Q .050 1.27 4
r .010 0.25 9
α 45° TP 45° TP 6
TECHNICAL DATA SHEET
6 Lake Street, Lawrence, MA 01841 Gort Road Business Park, Ennis, Co. Clare, Ireland
1-800-446-1158 / (978) 620-2600 / Fax: ( 978) 689-0803 Tel: +353 (0) 65 6840044 Fax: +353 (0) 65 6822298
Website: http://www.microsemi.com
T4-LDS-0064 Rev. 2 (110115) Page 4 of 4
NOTES:
1. Dimensions are in inches.
2. Millimeters are given for general information only.
3. In accordance with ASME Y14.5M, diameters are equivalent to φx
symbology.
4. Ceramic package only.
FIGURE 2. Physical dimensions for LCC.
Dimensions
Ltr Inches Millimeters
Min Max Min Max
BL .345 .360 8.76 9.14
BW .280 .295 7.11 7.49
CH .095 .115 2.41 2.92
LL1 .040 .055 1.02 1.40
LL2 .055 .065 1.40 1.65
LS .050 BSC 1.27 BSC
LS1 .025 BSC 0.635 BSC
LS2 .008 BSC 0.203 BSC
LW .020 .030 0.51 0.76
Q1 .105 REF 2.67 REF
Q2 .120 REF 3.05 REF
Q3 .045 .055 1.14 1.40
TL .070 .080 1.78 2.03
TW .120 .130 3.05 3.30
