NSVS1102 Jan-04 JRC SAW FILTER NSVS1102 Application 312.15MHz SAW FILTER Electrical Specification: (Table 1) The device characteristics are measured in the circuit shown in Fig.1. Table 1. Electrical Specifications Item Spec. Input and Output Impedance 50 Nominal Center Frequency (f0) 312.15MHz Insertion Loss 311.65~312.65MHz 3.0dB max. Response Variation 311.65~312.65MHz 1.5dB max. Input and Output VSWR 311.65~312.65MHz 2.5 max. Out of Band Rejection 290.75 MHz 50dB min. (Relative to Through Level) 333.55 MHz 40dB min. Temperature Range: -40~+85C Maximum Rating: (Table 2) Table 2. Maximum Ratings Item Maximum Input Power Maximum DC Voltage Operating Temperature Range Storage Temperature Rating +20dBm 7.5V -40~+85C -45~+90C Mechanical Specifications: (Fig.2) Package is designed as small as 3.0x3.0x1.15[mm3] for SMD (Surface Mount Device) type. Notice: This part is electrostatic discharge sensitive and may be damaged by improper handling. Communications Equipment Division Communications Equipment Marketing Department 10-1 Nishi-Shinjuku 6-chome, Shinjuku-ku, Tokyo. 160-8328 Japan Tel. +81 3-3348-3845 Fax. +81 3-3348-3935 http://www.jrc.co.jp/jp/product/device/saw/index.html (Japanese) http://www.jrc.co.jp/eng/product/comm/device/saw/saw_top_e.html (English) NSVS1102 Jan-04 IN 50 1 OUT 50 6 2 SAW 5 3 4 Fig.1 Measuring circuit ( ) 3 . 0 0 .1 5 ( ) ( ) 3.0 0.15 1.15 0.15 ( ) (0 .6) (0 .53 ) (0 .2 5) (0. 6) ( ) ( ) 10 ... X 11 ...Y 12 ...Z ( ) 1 9 ...0 10 19 ... 1 20 31 ... 2 ( ) [4 x ] (1.8) (0.75 ) (0. 45) [6x] Fig.2 Package dimensions (in mm) 0.93 3.8 1.15 3.8 0.6 2.2 0.93 1.15 Fig.3 Desirable land area (in mm) o. NSVS1102 Jan-04 Notice 1. Use this component within operating temperature range. It might not be satisfied with electrical specification without operating temperature range. When it is used less than -40C or more than +85C, it might be a cause of degradation or destruction of the component. Even if it endures during a short time, it causes degradation of qualification. 2. When soldering iron is used, solder with the temperature at the tip of soldering iron: 350C max., the time of soldering: 10 seconds max., the power of soldering iron: 30W max.. 3. Notice that the allowed time of soldering with soldering iron is accumulated time, when soldering is repeated. 4. As rapid temperature change for cleaning after reflow soldering might be a cause of destruction clean this component after confirming that temperature of this component goes down to room temperature. 5. Confirm that there are not any influence for qualification to this component in mounting on PCB when this component is cleaned. 6. As it might be a cause of degradation of destruction to apply static electricity to this component, do not apply static electricity or excessive voltage while assembling and measuring. And do not transport this component with bare hand. 7. As it might be a cause of degradation or destruction to apply D.C. voltage between each terminal, apply D.C. voltage 7.5V max. in actual circuit. Note 1. This specification specifies the quality of this component as a single unit. Make sure that this component is evaluated and confirmed against this specification when it is mounted to your products. Insertion Loss [dB] 312.15MHz SAW Filter FREQUENCY CHARACTERISTICS 0 0 10 1 20 2 30 3 40 4 50 5 60 6 70 7 80 8 90 9 287.2 292.2 297.2 302.2 307.2 312.2 317.2 322.2 327.2 332.2 337.2 Frequency [ MHz] S11 11 10 9 8 7 6 5 4 3 2 1 302.15 306.15 310.15 314.15 318.15 322.15 Frequency [MHz] S22 VSWR VSWR S11 S22 11 10 9 8 7 6 5 4 3 2 1 302.15 306.15 310.15 314.15 318.15 322.15 Frequency [MHz]