TECHNICAL DATA SHEET 6 Lake Street, Lawrence, MA 01841 1-800-446-1158 / (978) 620-2600 / Fax: (978) 689-0803 Website: http: //www.microsemi.com NPN SILICON SWITCHING TRANSISTOR Qualified per MIL-PRF-19500/255 DEVICES LEVELS 2N2221A 2N2221AL 2N2221AUA 2N2221AUB 2N2221AUBC * 2N2222A 2N2222AL 2N2222AUA 2N2222AUB 2N2222AUBC * JAN JANTX JANTXV JANS * Available to JANS quality level only. ABSOLUTE MAXIMUM RATINGS (TC = +25C unless otherwise noted) Parameters / Test Conditions Symbol Value Unit Collector-Emitter Voltage VCEO 50 Vdc Collector-Base Voltage VCBO 75 Vdc Emitter-Base Voltage VEBO 6.0 Vdc Collector Current IC 800 mAdc Total Power Dissipation @ TA = +25C PT 0.5 W Top, Tstg -65 to +200 C Symbol Max. Unit 325 210 325 C/W Operating & Storage Junction Temperature Range TO-18 (TO-206AA) 2N2221A, 2N2222A THERMAL CHARACTERISTICS Parameters / Test Conditions Thermal Resistance, Junction-to-Ambient 2N2221A, L 2N2222A, L RJA 2N2221AUA 2N2222AUA 2N2221AUB, UBC 2N2222AUB, UBC Note: Consult 19500/255 for thermal performance curves. 1. Derate linearly 3.08mW/C above TA > +37.5C 2. 4 PIN 2N2221AUA, 2N2222AUA Derate linearly 4.76mW/C above TA > +63.5C ELECTRICAL CHARACTERISTICS (TA = +25C, unless otherwise noted) Parameters / Test Conditions Symbol Min. V(BR)CEO 50 Max. Unit OFF CHARACTERTICS Collector-Emitter Breakdown Voltage IC = 10mAdc Collector-Base Cutoff Current VCB = 75Vdc VCB = 60Vdc Emitter-Base Cutoff Current VEB = 6.0Vdc VEB = 4.0Vdc Collector-Emitter Cutoff Current VCE = 50Vdc T4-LDS-0060 Rev. 2 (100247) Vdc ICBO 10 10 Adc Adc IEBO 10 10 Adc Adc ICES 50 Adc 3 PIN 2N2221AUB, 2N2222AUB 2N2221AUBC, 2N2222AUBC (UBC = Ceramic Lid Version) Page 1 of 6 TECHNICAL DATA SHEET 6 Lake Street, Lawrence, MA 01841 1-800-446-1158 / (978) 620-2600 / Fax: (978) 689-0803 Website: http: //www.microsemi.com ELECTRICAL CHARACTERISTICS (TA = +25C, unless otherwise noted) Parameters / Test Conditions ON CHARACTERISTICS Symbol Min. Max. Unit (2) Forward-Current Transfer Ratio IC = 0.1mAdc, VCE = 10Vdc 2N2221A, L, UA, UB, UBC 2N2222A, L, UA, UB, UBC 30 50 IC = 1.0mAdc, VCE = 10Vdc 2N2221A, L, UA, UB, UBC 2N2222A, L, UA, UB, UBC 35 75 IC = 10mAdc, VCE = 10Vdc 2N2221A, L, UA, UB, UBC 2N2222A, L, UA, UB, UBC IC = 150mAdc, VCE = 10Vdc 2N2221A, L, UA, UB, UBC 2N2222A, L, UA, UB, UBC 40 100 IC = 500mAdc, VCE = 10Vdc 2N2221A, L, UA, UB, UBC 2N2222A, L, UA, UB, UBC 20 30 hFE Collector-Emitter Saturation Voltage IC = 150mAdc, IB = 15mAdc IC = 500mAdc, IB = 50mAdc VCE(sat) Base-Emitter Voltage IC = 150mAdc, IB = 15mAdc IC = 500mAdc, IB = 50mAdc VBE(sat) 150 325 40 100 120 300 0.3 1.0 Vdc 0.6 1.2 2.0 Vdc Symbol Min. Max. Unit hfe 30 50 Cobo 8.0 pF Cibo 25 pF Max. Unit ton 35 s toff 300 s DYNAMIC CHARACTERISTICS Parameters / Test Conditions Small-Signal Short-Circuit Forward Current Transfer Ratio IC = 1.0mAdc, VCE = 10Vdc, f = 1.0kHz 2N2221A, L, UA, UB, UBC 2N2222A, L, UA, UB, UBC Magnitude of Small-Signal Short-Circuit Forward Current Transfer Ratio IC = 20mAdc, VCE = 20Vdc, f = 100MHz |hfe| 2.5 Output Capacitance VCB = 10Vdc, IE = 0, 100kHz f 1.0MHz Input Capacitance VEB = 0.5Vdc, IC = 0, 100kHz f 1.0MHz SWITCHING CHARACTERISTICS Parameters / Test Conditions Turn-On Time See figure 8 of MIL-PRF-19500/255 Turn-Off Time See Figure 9 of MIL-PRF-19500/255 Symbol Min. (2) Pulse Test: Pulse Width = 300s, Duty Cycle 2.0%. T4-LDS-0060 Rev. 2 (100247) Page 2 of 6 TECHNICAL DATA SHEET 6 Lake Street, Lawrence, MA 01841 1-800-446-1158 / (978) 620-2600 / Fax: (978) 689-0803 Website: http: //www.microsemi.com PACKAGE DIMENSIONS NOTES: 1. Dimensions are in inches. 2. Millimeters are given for general information only. 3. Beyond r (radius) maximum, TL shall be held for a minimum length of .011 inch (0.28 mm). 4. Dimension TL measured from maximum HD. 5. Body contour optional within zone defined by HD, CD, and Q. 6. Leads at gauge plane .054 +.001 -.000 inch (1.37 +0.03 -0.00 mm) below seating plane shall be within .007 inch (0.18 mm) radius of true position (TP) at maximum material condition (MMC) relative to tab at MMC. 7. Dimension LU applies between L1 and L2. Dimension LD applies between L2 and LL minimum. Diameter is uncontrolled in L1 and beyond LL minimum. 8. All three leads. 9. The collector shall be internally connected to the case. 10. Dimension r (radius) applies to both inside corners of tab. 11. In accordance with ASME Y14.5M, diameters are equivalent to x symbology. 12. Lead 1 = emitter, lead 2 = base, lead 3 = collector. 13. For L suffix devices, dimension LL = 1.5 inches (38.10 mm) min. and 1.75 inches (44.45 mm) max. Symbol CD CH HD LC LD LL LU L1 L2 P Q TL TW r Dimensions Inches Millimeters Min Max Min Max .178 .195 4.52 4.95 .170 .210 4.32 5.33 .209 .230 5.31 5.84 .100 TP 2.54 TP .016 .021 0.41 0.53 .500 .750 12.70 19.05 .016 .019 0.41 0.48 .050 1.27 .250 6.35 .100 2.54 .030 0.76 .028 .048 0.71 1.22 .036 .046 0.91 1.17 .010 0.25 45 TP 45 TP 1, 2, 9, 11, 12, 13 Note 6 7,8 7,8,13 7,8 7,8 7,8 5 3,4 3 10 6 FIGURE 1. Physical dimensions (similar to TO-18). T4-LDS-0060 Rev. 2 (100247) Page 3 of 6 TECHNICAL DATA SHEET 6 Lake Street, Lawrence, MA 01841 1-800-446-1158 / (978) 620-2600 / Fax: (978) 689-0803 Website: http: //www.microsemi.com NOTES: 1. Dimensions are in inches. 2. Millimeters are given for general information only. 3. Dimension CH controls the overall package thickness. When a window lid is used, dimension CH must increase by a minimum of .010 inch (0.254 mm) and a maximum of .040 inch (1.020 mm). 4. The corner shape (square, notch, radius) may vary at the manufacturer's option, from that shown on the drawing. 5. Dimensions LW2 minimum and L3 minimum and the appropriate castellation length define an unobstructed three-dimensional space traversing all of the ceramic layers in which a castellation was designed. (Castellations are required on the bottom two layers, optional on the top ceramic layer.) Dimension LW2 maximum and L3 maximum define the maximum width and depth of the castellation at any point on its surface. Measurement of these dimensions may be made prior to solder dipping. 6. The co-planarity deviation of all terminal contact points, as defined by the device seating plane, shall not exceed .006 inch (0.15mm) for solder dipped leadless chip carriers. 7. In accordance with ASME Y14.5M, diameters are equivalent to x symbology. Symbol BL BL2 BW BW2 CH L3 LH LL1 LL2 LS LW LW2 Pin no. Transistor Dimensions Inches Millimeters Min Max Min Max .215 .225 5.46 5.71 .225 5.71 .145 .155 3.68 3.93 .155 3.93 .061 .075 1.55 1.90 .003 .007 0.08 0.18 .029 .042 0.74 1.07 .032 .048 0.81 1.22 .072 .088 1.83 2.23 .045 .055 1.14 1.39 .022 .028 0.56 0.71 .006 .022 0.15 0.56 1 Collector 2 Emitter 3 Base Note 3 5 5 4 N/C FIGURE 2. Physical dimensions, surface mount (UA version). T4-LDS-0060 Rev. 2 (100247) Page 4 of 6 TECHNICAL DATA SHEET 6 Lake Street, Lawrence, MA 01841 1-800-446-1158 / (978) 620-2600 / Fax: (978) 689-0803 Website: http: //www.microsemi.com UB Symbol BH BL BW CL CW LL1 LL2 Dimensions Inches Millimeters Min Max Min Max .046 .056 1.17 1.42 .115 .128 2.92 3.25 .085 .108 2.16 2.74 .128 3.25 .108 2.74 .022 .038 0.56 0.96 .017 .035 0.43 0.89 Note Symbol LS1 LS2 LW r r1 r2 Dimensions Inches Millimeters Min Max Min Max .036 .040 0.91 1.02 .071 .079 1.81 2.01 .016 .024 0.41 0.61 .008 .203 .012 .305 .022 .559 Note NOTES: 1. Dimensions are in inches. 2. Millimeters are given for general information only. 3. Hatched areas on package denote metalized areas. 4. Pad 1 = Base, Pad 2 = Emitter, Pad 3 = Collector, Pad 4 = Shielding connected to the lid. 5. In accordance with ASME Y14.5M, diameters are equivalent to x symbology. FIGURE 3. Physical dimensions, surface mount (UB version) T4-LDS-0060 Rev. 2 (100247) Page 5 of 6 TECHNICAL DATA SHEET 6 Lake Street, Lawrence, MA 01841 1-800-446-1158 / (978) 620-2600 / Fax: (978) 689-0803 Website: http: //www.microsemi.com UBC Symbol BH BL BW CL CW LL1 LL2 Dimensions Inches Millimeters Min Max Min Max .046 .071 1.17 1.80 .115 .128 2.92 3.25 .085 .108 2.16 2.74 .128 3.25 .108 2.74 .022 .038 0.56 0.96 .017 .035 0.43 0.89 Note Symbol LS1 LS2 LW r r1 r2 Dimensions Inches Millimeters Min Max Min Max .036 .040 0.91 1.02 .071 .079 1.81 2.01 .016 .024 0.41 0.61 .008 .203 .012 .305 .022 .559 Note NOTES: 1. Dimensions are in inches. 2. Millimeters are given for general information only. 3. Hatched areas on package denote metalized areas. 4. Pad 1 = Base, Pad 2 = Emitter, Pad 3 = Collector, Pad 4 = Connected to the lid braze ring. 5. In accordance with ASME Y14.5M, diameters are equivalent to x symbology. FIGURE 4. Physical dimensions, surface mount (UBC version, ceramic lid) T4-LDS-0060 Rev. 2 (100247) Page 6 of 6 Mouser Electronics Authorized Distributor Click to View Pricing, Inventory, Delivery & Lifecycle Information: Microsemi: JANS2N2222AUB 2N2222AL 2N2222A 2N2221A 2N2222AUA 2N2221AUB 2N2221AUA 2N2221AL 2N2222AUB JAN2N2221AL Jantx2N2222A Jan2N2222A JANS2N2221AUB Jantxv2N2222AUB JANS2N2221A Jantx2N2221AUA Jantxv2N2222AL Jantxv2N2221AUA JANS2N2222A Jan2N2221AUA Jantxv2N2221A Jan2N2222AL JANTX2N2221AL Jantx2N2221AUB JANTXV2N2221AL Jantx2N2222AUA JANS2N2222AUA Jan2N2221AUB Jan2N2221A Jantx2N2222AUB Jantx2N2222AL Jantxv2N2222A Jantxv2N2222AUA JANS2N2222AL Jan2N2222AUA JANS2N2221AL Jantx2N2221A JANS2N2221AUA